Hardware

Home/Hardware
  • Out of stock

    Brass Pivot Hinge for Transoms

    Brass pivot hinge for transoms include one hinge- the pin side and the receiver side. You will need to order two in order to do one sash. These are solid Brass with a lacquered finish.

    The pin side has the following measurements:

    Center to center of screw hole 1-1/8″

    Face of Hinge -2-3/8″ tall, 1″ wide, and mortises 1/8″ into the face of the transom.

    Side of hinge- 3/4″ tall, 1- 1/16″ wide, 3/16″ thick, center of pin to edge 7/8″, pin diameter 7/16″, pin length 15/16″

    The receiver side has the following measurements:

    Center to center of screw hole 1-1/4″

    Diameter of center hole 3/8″

    1-15/16″ tall, 7/8″ wide and 1/4″ deep

    Brass Pivot Hinge

  • # 3 Right Lull and Porter Style Shutter Hinge

    #3 Right Lull & Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.

    Hinge Width when open - 3-1/4"

    Hinge throw from casing - 1-3/8"

    Hinge height at mortise -2-9/16"

    These do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.

    3 right open rear

  • 6 Inch Shutter Pull

    6 Inch Shutter Pull. These pulls are usually located on the inner stile of a shutter in order to close it from inside of your window. The handle is done in a bail style and folds away to a 1/4" profile when not in use. These do not come with screws. The rear plate is steel and the handle is cast iron. They come powder coated in a matte black finish.

    The Shutter Pulls have the following dimensions:

    Height- 6-1/4"

    Width- 1"

    Center to Center of outer Screw Holes- 5-1/2"

    Handle height- 3-7/8"

    Handle Depth- 1-1/4"

    6 inch shutter pull

  • # 3 Left Lull and Porter style Shutter Hinge

    # 3 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.

    Hinge Width when open – 3-1/4″

    Hinge throw from casing – 1-1/2″

    Hinge Height at mortise- 2-9/16"

    They do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.

    3 left open rear

  • Shutter Catches

    Shutter Catches. These typically mount at the bottom of the shutter and latch to the sill of the window. These can only be used when you can open your window and access the rear of your shutters. The set comes with one latch an one catch, you will need two sets for each pair of shutters. Both pieces are made of cast iron. We recommend you prime and paint these before installation and screw them in with a screwdriver by hand, not with a drill. These do not come with screws.

     cincinatti catch

  • 8 Inch Shutter Slide Bolt

    8 Inch Shutter Slide Bolt. These slide shutter bolts are meant to mount to a pair of shutters in the space between the shutter and the window and function to fasten the shutters during a storm. The back plate, keeper, and straps are made of steel and the bolt itself is made of cast iron. They are powder coated in a glossy black finish.
    • They do not come with screws.
    • The back plate at the rear of the bolt measures 6-1/16″ x 1-11/16″
    • The bolt measures 7-51/16″ x 7/8″
    • The handle of the bolt projects 1-1/16″ from the rear
    • The keeper measures 2-1/4″ x 1-3/4″
    • The bolt throws 2-5/8″ out from the rear plate

    Ricca’s Architectural Sales

    511 North Solomon Street, New Orleans, LA 70119 (504) 488 – 5524 or (504) 822-8200 Fax: (504) 488 – 5662, Email: riccaarch@yahoo.com
    Business Hours:
    Tuesday – Friday 9 am – 5 pm Saturday – 9 am – 4 pm

    8 inch shutter slide bolt

  • Iron Parliament Hinge with Three Inch Offset

    Iron Parliament Hinge with Three Inch Offset measures a total of 5-1/8" wide and 2-7/8" tall. It mortises into the door or jamb 1" x 2-7/8" and has a throw of 3" when open. The pin on the hinge is removable making it function as either a right or left hand swing.

    five and an eigth parlament hinge

  • # 2  1/2 Right lull and Porter style Shutter Hinge

    # 2  1/2 Right Lull and Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.

    Hinge Width when open - 3-7/8"

    Hinge Throw from casing - 2-3/16"

    Hinge Height at mortise- 2-7/16"

    They do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a  drill.

    two and a half Right open rear

  • #  2 1/2 Left Lull and Porter style Shutter Hinge

    # 2 1/2 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.

    Hinge Width when open - 3-13/16"

    Hinge throw from casing - 2-1/16"

    Hinge Height at mortise - 2-9/16"

    They do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a  drill.

    two and a half left open rear

  • 6 Inch Shutter Slide Bolt

    6 Inch Shutter Slide Bolt. These slide bolts are meant to mount to a pair of shutters in the space between the shutter and the window and function to fasten the shutters during a storm. The back plate, keeper, and straps are made of steel and the bolt itself is made of cast iron. They are powder coated in a glossy black finish.

    They do not come with screws.

    The back plate at the rear of the bolt measures 5" x 1-3/4"

    The bolt measures 6-11/16" x 13/16"

    The handle of the bolt projects 1-1/16" from the rear

    The keeper measures 2-1/4" x 1-3/4"

    The bolt throws 1-15/16" out from the rear plate

    6 inch shutter slide bolt

  • Out of stock

    Brass Sash Pulley

    Brass Sash Pulley measures 4-3/4″ x 1-1/4″ at the face, it mortises 2-1/4″ deep into the jamb of the window.

    Brass Window Pulley

  • Brass Through Shutter Latch

    Brass Through Shutter Latch. These solid brass shutter latches are polished and lacquered to prevent immediate tarnish. They are intended to be mortised through the bottom of the shutter and hook to their keeper mounted on the window sill. When open they connect to a keeper mounted on the exterior of the home. These latches take the place of both dogs and slide bolts. These latches are meant for use on shutters 1-3/8" thick or less.  Each kit includes the latch, a plate for the rear of the shutter, a keeper for the sill, and a keeper for the wall. One kit will do a single shutter, you will need two kits for each window.

    The latch itself (the part that goes through the shutter) measures 2-3/8" at the top and 1-15/16" at the bottom

    The pull (the piece that you would operate) measures-1-1/4" tall and projects out 2" at the most (latch is 1-3/8" from the plate)

    The plate connected to the latch is 2" wide and 1-1/2" tall

    The plate that goes on the rear measures 1-3/8" tall and 1-1/2" wide

    The sill keeper (looks like bottle opener) is 1-3/4" deep and 1" wide

    The wall keeper (L shaped) is 1-1/16" tall, 15/16" wide and projects 1" from the wall

    Brass Through Shutter Latch Kit

  • # 0 Right Lull and Porter style Shutter Hinge

    # 0 Right Lull and Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.

    Hinge Width when open - 6-7/16"

    Hinge throw from casing - 4-1/8"

    Hinge Height at mortise-3-1/2"

    These do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a  drill.

     

    0 right open rear

  • Out of stock

    Brass Knuckle Sash Lock

    Brass Knuckle Sash Lock is meant for use with double hung windows. The lock comes with two pieces, the latching part, and the receiver which gets overlapped. These were found on most double hung sashes in New Orleans that predated the 1910's. The base of the latching part measures 1-7/8" x 13/16". The base of the receiver measures 1-7/8" x  3/4". It is made of solid brass.

    Brass Knuckle Sash Lock

  • # 1 1/2 Left Lull and Porter style Shutter Hinge

    # 1 1/2 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.

    Hinge Width when open - 5-1/8"

    Hinge throw from casing - 3-1/4"

    Hinge Height at mortise- 3"

    They do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.

    one and a half left open rear

  • Iron Pivot Hinge for Transoms

    Iron pivot hinge for transoms include one hinge- the pin side and the receiver side. You will need to order two in order to do one sash. These are made of cast iron and left unfinished.

    The pin side has the following measurements:

    Center to center of screw hole 1-1/2"

    Face of Hinge -2-3/8" tall, 7/8" wide, and mortises 1/8" into the face of the transom.

    Side of hinge- 5/8" tall, 7/8" wide, 1/8" thick, center of pin to edge 3/4", pin diameter 3/8", pin length 11/16"

    The receiver side has the following measurements:

    Center to center of screw hole 1-1/8"

    Diameter of center hole 7/16"

    1-11/16" tall, 3/4" wide and 1/8" deep

    Iron Pivot Hinges

  • # 1 1/2 Right Lull and Porter style Shutter Hinge

    # 1 1/2 Right Lull and Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.

    Hinge Width when open - 5"

    Hinge throw from casing - 3-1/4"

    Hinge Height at mortise - 2-7/8"

    They do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.

    one and a half right open rear

  • # 0 Left Lull and Porter style Shutter Hinge

    # 0 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.

    Hinge Width when open - 6-7/16"

    Hinge throw from casing - 4-1/8"

    Hinge Height at mortise- 3-1/2"

    These do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a  drill.

    0 left open rear

  • Out of stock

    Brass Oval Beaded Sash Lift

    Brass Oval Beaded Sash Lift measures 4" x 2" and mortises into the sash 3/8" deep at 2-3/4" x 1-1/4".

    Oval Beaded Sash Lift

  • # 1 Left Lull and Porter style Shutter Hinges

    # 1 Left Lull and Porter style Shutter Hinges. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.

    Hinge Width when open - 5-1/2"

    Hinge throw from casing - 3-11/16"

    Hinge Height at mortise-3-3/16"

    These do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a  drill.

     1 left open rear

  • Out of stock

    Brass Transom Latch

    Brass Transom Latch can be used in conjunction with pivoting transom hinges and would mount on the bottom rail of the transom, with the strike plate being mortised to the bottom of the transom's jamb. The latch is operated by pulling up on the loop at the top. (one of our clients suggests mounting a hook to the top of a broom stick to avoid getting on a stool.) The latch measures 2-1/8" wide, 1-1/4" tall, and 5/8" deep (with the loop standing 1-3/8" deep). The strike plate measures 1-3/4" wide, 1-1/2" deep, and mortises 1-3/4" x 3/4"x 3/16" into the jamb. It is made out of solid brass.

    Brass Transom Latch

  • # 2 Right Lull and Porter style Shutter Hinge

    # 2 Right Lull and Porter style Shutter Hinge. Right shutter hinge mounts on the left side of the window when looking at the window from outside of your home.

    Hinge Width when open - 4-7/16"

    Hinge throw from casing - 2-1/2"

    Hinge Height at mortise-2-7/8"

    They do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.

     2 right open rear

  • 12 Inch Shutter Slide Bolt

    12 Inch Shutter Slide Bolt. These slide bolts are meant to mount to a pair of shutters in the space between the shutter and the window and function to fasten the shutters during a storm. The back plate, keeper, and straps are made of steel and the bolt itself is made of cast iron. They are powder coated in a glossy black finish.

    They do not come with screws.

    The back plate at the rear of the bolt measures 8-13/16″ x 2-1/16″

    The bolt measures 8-3/16″ x 7/8″

    The handle of the bolt projects 3/4″ from the rear

    The keeper measures 3-13/16″ x 2-1/16″

    The bolt throws 3-3/4″ out from the rear plate

    12 Inch Shutter Slide Bolt12in Shutter Slide

  • # 2 Left Lull and Porter style Shutter Hinge

    # 2 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.

    Hinge Width when open - 4-7/16"

    Hinge throw from casing - 2-5/8"

    Hinge Height at mortise- 2-15/16"

    They do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.

    2 left open rear

Title

Go to Top