-
Out of stock
Small Soffit Vent
Small Soffit Vent measures 11-5/8" in diameter. They are made of cast aluminum, and sold unfinished. These can be used for venting the attic from your soffit, or look great as a decorative piece on a wooden gate.
-
Out of stock
Brass Pivot Hinge for Transoms
Brass pivot hinge for transoms include one hinge- the pin side and the receiver side. You will need to order two in order to do one sash. These are solid Brass with a lacquered finish.
The pin side has the following measurements:
Center to center of screw hole 1-1/8″
Face of Hinge -2-3/8″ tall, 1″ wide, and mortises 1/8″ into the face of the transom.
Side of hinge- 3/4″ tall, 1- 1/16″ wide, 3/16″ thick, center of pin to edge 7/8″, pin diameter 7/16″, pin length 15/16″
The receiver side has the following measurements:
Center to center of screw hole 1-1/4″
Diameter of center hole 3/8″
1-15/16″ tall, 7/8″ wide and 1/4″ deep
-
# 3 Right Lull and Porter Style Shutter Hinge
#3 Right Lull & Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.
Hinge Width when open - 3-1/4"
Hinge throw from casing - 1-3/8"
Hinge height at mortise -2-9/16"
These do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
Flat Victorian Foundation Vent
Flat Victorian Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally are screwed to the foundation. The measurement is 21-3/8″ wide and 13-5/8″ tall. The vent does not recess.
-
6 Inch Shutter Pull
6 Inch Shutter Pull. These pulls are usually located on the inner stile of a shutter in order to close it from inside of your window. The handle is done in a bail style and folds away to a 1/4" profile when not in use. These do not come with screws. The rear plate is steel and the handle is cast iron. They come powder coated in a matte black finish.
The Shutter Pulls have the following dimensions:
Height- 6-1/4"
Width- 1"
Center to Center of outer Screw Holes- 5-1/2"
Handle height- 3-7/8"
Handle Depth- 1-1/4"
-
Large Soffit Vent
Large Soffit Vent measures 17-1/16" in diameter. They are made of cast aluminum, and sold unfinished. These can be used for venting the attic from your soffit, or look great as a decorative piece on a wooden gate.
-
# 3 Left Lull and Porter style Shutter Hinge
# 3 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.
Hinge Width when open – 3-1/4″
Hinge throw from casing – 1-1/2″
Hinge Height at mortise- 2-9/16"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
Out of stock
Medium Soffit Vent
Medium Soffit Vent measures 13-1/16" in diameter. They are made of cast aluminum, and sold unfinished. These can be used for venting the attic from your soffit, or look great as a decorative piece on a wooden gate, or even covers for can lighting on your front porch.
-
Shutter Catches
Shutter Catches. These typically mount at the bottom of the shutter and latch to the sill of the window. These can only be used when you can open your window and access the rear of your shutters. The set comes with one latch an one catch, you will need two sets for each pair of shutters. Both pieces are made of cast iron. We recommend you prime and paint these before installation and screw them in with a screwdriver by hand, not with a drill. These do not come with screws.
-
Small Victorian Foundation Vent
Small Victorian Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 13″ wide and 8″ tall. The front measurement is 17-3/4″ wide and 12-1/4″ tall. The vent recesses into the foundation 3-1/2″ deep.
-
8 Inch Shutter Slide Bolt
8 Inch Shutter Slide Bolt. These slide shutter bolts are meant to mount to a pair of shutters in the space between the shutter and the window and function to fasten the shutters during a storm. The back plate, keeper, and straps are made of steel and the bolt itself is made of cast iron. They are powder coated in a glossy black finish.- They do not come with screws.
- The back plate at the rear of the bolt measures 6-1/16″ x 1-11/16″
- The bolt measures 7-51/16″ x 7/8″
- The handle of the bolt projects 1-1/16″ from the rear
- The keeper measures 2-1/4″ x 1-3/4″
- The bolt throws 2-5/8″ out from the rear plate
Ricca’s Architectural Sales
511 North Solomon Street, New Orleans, LA 70119 (504) 488 – 5524 or (504) 822-8200 Fax: (504) 488 – 5662, Email: riccaarch@yahoo.com
Business Hours:
Tuesday – Friday 9 am – 5 pm Saturday – 9 am – 4 pm
-
Iron Parliament Hinge with Three Inch Offset
Iron Parliament Hinge with Three Inch Offset measures a total of 5-1/8" wide and 2-7/8" tall. It mortises into the door or jamb 1" x 2-7/8" and has a throw of 3" when open. The pin on the hinge is removable making it function as either a right or left hand swing.
-
# 2 1/2 Right lull and Porter style Shutter Hinge
# 2 1/2 Right Lull and Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.
Hinge Width when open - 3-7/8"
Hinge Throw from casing - 2-3/16"
Hinge Height at mortise- 2-7/16"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
# 2 1/2 Left Lull and Porter style Shutter Hinge
# 2 1/2 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.
Hinge Width when open - 3-13/16"
Hinge throw from casing - 2-1/16"
Hinge Height at mortise - 2-9/16"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
6 Inch Shutter Slide Bolt
6 Inch Shutter Slide Bolt. These slide bolts are meant to mount to a pair of shutters in the space between the shutter and the window and function to fasten the shutters during a storm. The back plate, keeper, and straps are made of steel and the bolt itself is made of cast iron. They are powder coated in a glossy black finish.
They do not come with screws.
The back plate at the rear of the bolt measures 5" x 1-3/4"
The bolt measures 6-11/16" x 13/16"
The handle of the bolt projects 1-1/16" from the rear
The keeper measures 2-1/4" x 1-3/4"
The bolt throws 1-15/16" out from the rear plate
-
Out of stock
Brass Sash Pulley
Brass Sash Pulley measures 4-3/4″ x 1-1/4″ at the face, it mortises 2-1/4″ deep into the jamb of the window.
-
Brass Through Shutter Latch
Brass Through Shutter Latch. These solid brass shutter latches are polished and lacquered to prevent immediate tarnish. They are intended to be mortised through the bottom of the shutter and hook to their keeper mounted on the window sill. When open they connect to a keeper mounted on the exterior of the home. These latches take the place of both dogs and slide bolts. These latches are meant for use on shutters 1-3/8" thick or less. Each kit includes the latch, a plate for the rear of the shutter, a keeper for the sill, and a keeper for the wall. One kit will do a single shutter, you will need two kits for each window.
The latch itself (the part that goes through the shutter) measures 2-3/8" at the top and 1-15/16" at the bottom
The pull (the piece that you would operate) measures-1-1/4" tall and projects out 2" at the most (latch is 1-3/8" from the plate)
The plate connected to the latch is 2" wide and 1-1/2" tall
The plate that goes on the rear measures 1-3/8" tall and 1-1/2" wide
The sill keeper (looks like bottle opener) is 1-3/4" deep and 1" wide
The wall keeper (L shaped) is 1-1/16" tall, 15/16" wide and projects 1" from the wall
-
# 0 Right Lull and Porter style Shutter Hinge
# 0 Right Lull and Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.
Hinge Width when open - 6-7/16"
Hinge throw from casing - 4-1/8"
Hinge Height at mortise-3-1/2"
These do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
Small Rectangular Foundation Vent
Small Rectangular Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 13″ wide and 7-7/8″ tall. The front measurement is 15-1/8″ wide and 10-1/8″ tall. The vent recesses into the foundation 3″ deep.
-
Out of stock
Brass Knuckle Sash Lock
Brass Knuckle Sash Lock is meant for use with double hung windows. The lock comes with two pieces, the latching part, and the receiver which gets overlapped. These were found on most double hung sashes in New Orleans that predated the 1910's. The base of the latching part measures 1-7/8" x 13/16". The base of the receiver measures 1-7/8" x 3/4". It is made of solid brass.
-
# 1 1/2 Left Lull and Porter style Shutter Hinge
# 1 1/2 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.
Hinge Width when open - 5-1/8"
Hinge throw from casing - 3-1/4"
Hinge Height at mortise- 3"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
Iron Pivot Hinge for Transoms
Iron pivot hinge for transoms include one hinge- the pin side and the receiver side. You will need to order two in order to do one sash. These are made of cast iron and left unfinished.
The pin side has the following measurements:
Center to center of screw hole 1-1/2"
Face of Hinge -2-3/8" tall, 7/8" wide, and mortises 1/8" into the face of the transom.
Side of hinge- 5/8" tall, 7/8" wide, 1/8" thick, center of pin to edge 3/4", pin diameter 3/8", pin length 11/16"
The receiver side has the following measurements:
Center to center of screw hole 1-1/8"
Diameter of center hole 7/16"
1-11/16" tall, 3/4" wide and 1/8" deep
-
Medium Victorian Foundation Vent
Medium Victorian Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 17-7/8″ wide and 9-3/8″ tall. The front measurement is 22-7/8″ wide and 14-3/8″ tall. The vent recesses into the foundation 3-1/2″ deep.
-
# 1 1/2 Right Lull and Porter style Shutter Hinge
# 1 1/2 Right Lull and Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.
Hinge Width when open - 5"
Hinge throw from casing - 3-1/4"
Hinge Height at mortise - 2-7/8"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
