Shop

Home/Shop
  • Medium Victorian Foundation Vent

    Medium Victorian Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 17-7/8″ wide and 9-3/8″ tall. The front measurement is 22-7/8″ wide and 14-3/8″ tall. The vent recesses into the foundation 3-1/2″ deep.

    medium victorian foundation

  • Large Victorian Foundation Vent

    Large Victorian Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 19″ wide and 10-5/8″ tall. The front measurement is 24-5/8″ wide and 16-1/4″ tall. The vent recesses into the foundation 3″ deep.

    large victorian foundation vent

  • Small Rectangular Foundation Vent

    Small Rectangular Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 13″ wide and 7-7/8″ tall. The front measurement is 15-1/8″ wide and 10-1/8″ tall. The vent recesses into the foundation 3″ deep.

    small rectangular foundation

  • Small Plain Oval Foundation Vent

    Small Plain Oval Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 12″ wide and 6-1/2″ tall. The front measurement is 15-7/8″ wide and 10-1/4″ tall. The vent recesses into the foundation 3″ deep.

    small oval foundation vent

  • Out of stock

    Flat Victorian Foundation Vent

    Flat Victorian Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally are screwed to the foundation. The measurement is 21-3/8″ wide and 13-5/8″ tall. The vent does not recess.

    Flat Foundation

  • Large Rectangular Foundation Vent

    Large Rectangular Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 14-1/4" wide and 8-5/8" tall. The front measurement is 17-1/2" wide and 11-3/4" tall. The vent recesses into the foundation 3" deep.

    large rectangular foundation vent

  • Large Plain Oval Foundation Vent

    Large Plain Oval Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 14″ wide and 8-1/4″ tall. The front measurement is 18-1/4″ wide and 12-3/8″ tall. The vent recesses into the foundation 3-3/8″ deep.

    large oval foundation

  • Brass Transom Latch

    Brass Transom Latch can be used in conjunction with pivoting transom hinges and would mount on the bottom rail of the transom, with the strike plate being mortised to the bottom of the transom's jamb. The latch is operated by pulling up on the loop at the top. (one of our clients suggests mounting a hook to the top of a broom stick to avoid getting on a stool.) The latch measures 2-1/8" wide, 1-1/4" tall, and 5/8" deep (with the loop standing 1-3/8" deep). The strike plate measures 1-3/4" wide, 1-1/2" deep, and mortises 1-3/4" x 3/4"x 3/16" into the jamb. It is made out of solid brass.

    Brass Transom Latch

  • Iron Transom Latch

    Iron Transom Latch can be used in conjunction with pivoting transom hinges and would mount on the bottom rail of the transom, with the strike plate being mortised to the bottom of the transom's jamb. The latch is operated by pulling up on the loop at the top. (one of our clients suggests mounting a hook to the top of a broom stick to avoid getting on a stool.) The latch measures 2-1/8" wide, 1-1/4" tall, and 5/8" deep (with the loop standing 1-3/8" deep). The strike plate measures 1-3/4" wide, 1-1/2" deep, and mortises 1-3/4" x 3/4"x 3/16" into the jamb. It is made out of cast iron and painted black.

    Iron transom Latch

  • Brass Pivot Hinge for Transoms

    Brass pivot hinge for transoms include one hinge- the pin side and the receiver side. You will need to order two in order to do one sash. These are solid Brass with a lacquered finish.

    The pin side has the following measurements:

    Center to center of screw hole 1-1/8″

    Face of Hinge -2-3/8″ tall, 1″ wide, and mortises 1/8″ into the face of the transom.

    Side of hinge- 3/4″ tall, 1- 1/16″ wide, 3/16″ thick, center of pin to edge 7/8″, pin diameter 7/16″, pin length 15/16″

    The receiver side has the following measurements:

    Center to center of screw hole 1-1/4″

    Diameter of center hole 3/8″

    1-15/16″ tall, 7/8″ wide and 1/4″ deep

    Brass Pivot Hinge

  • Iron Pivot Hinge for Transoms

    Iron pivot hinge for transoms include one hinge- the pin side and the receiver side. You will need to order two in order to do one sash. These are made of cast iron and left unfinished.

    The pin side has the following measurements:

    Center to center of screw hole 1-1/2"

    Face of Hinge -2-3/8" tall, 7/8" wide, and mortises 1/8" into the face of the transom.

    Side of hinge- 5/8" tall, 7/8" wide, 1/8" thick, center of pin to edge 3/4", pin diameter 3/8", pin length 11/16"

    The receiver side has the following measurements:

    Center to center of screw hole 1-1/8"

    Diameter of center hole 7/16"

    1-11/16" tall, 3/4" wide and 1/8" deep

    Iron Pivot Hinges

  • Brass Embossed Sash Lock

    Brass Embossed Sash Lock can be used either with casement or double hung windows. With double hung sashes the moving part of the latch would mount to the bottom sash and the keeper would mount to the top sash.  The back plate of the keeper measures 2-3/8" x 7/8" and is a total of 3/4" tall. The back plate of the moving part of the latch measures 2-3/8" x 1-1/8". The arm measures 3-1/4" x 1".

    Brass Embossed Sash Lock

  • Brass Sash Pulley

    Brass Sash Pulley measures 4-3/4″ x 1-1/4″ at the face, it mortises 2-1/4″ deep into the jamb of the window.

    Brass Window Pulley

  • Iron Sash Pulley

    Iron Sash Pulley measures 4-3/4" x 1-1/4" at the face, it mortises 2-3/8" deep into the jamb of the window.

    Iron-window-pulley

  • Iron Window Y

    Iron Window Y's are used when the sash no longer stays up on it's own due to damaged or missing sash weights and balances. They mount to the jamb at about the level you want your window open and with a loose screw will pivot in or out of the way of the sash. The bottom of the sash is held up by the v shaped section, with the short end facing the exterior of the home.

    The Y measures 2-5/8" long, 2" at it's widest point, and 1/4" thick. It is made of cast iron and painted white.

    window y

  • Brass Victorian Sash Lift

    Brass Victorian Sash Lift measures 5-1/4" x 1-3/4" and mortises 3/8" deep at 2-3/4" x 1-1/8".

    Victorian Sash Lift

  • Out of stock

    Brass Oval Beaded Sash Lift

    Brass Oval Beaded Sash Lift measures 4" x 2" and mortises into the sash 3/8" deep at 2-3/4" x 1-1/4".

    Oval Beaded Sash Lift

  • Brass Casement Stay

    Brass Casement Stay is made to secure casement windows in either a closed or open position. The Maximum throw is 10-1/2". These are meant for use in an outswing application only.

    brass casement stay

  • Iron Casement Stay

    Iron Casement Stay is made to secure casement windows in either a closed or open position. The Maximum throw is 10-1/2". These are meant for use in an outswing application only.

    iron casement stay

  • # 00 Left Lull and Porter style Shutter Hinge

    # 00 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.

    Hinge Width when open – 8-7/8″

    Hinge throw from casing – 6″

    Hinge Height at mortise- 3-15/16″

    They do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.

    00 Left lull and porter style shutter hinge open rear

  • # 00 Right Lull and Porter Style Shutter Hinge

    # 00 Right Lull & Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.

    Hinge Width when open – 8-3/4″

    Hinge throw from casing – 6″

    Hinge height at mortise -3-15/16″

    These do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.

    00 Right lull and porter style shutter hinge open rear

  • # 0 Left Lull and Porter style Shutter Hinge

    # 0 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.

    Hinge Width when open - 6-7/16"

    Hinge throw from casing - 4-1/8"

    Hinge Height at mortise- 3-1/2"

    These do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a  drill.

    0 left open rear

  • # 0 Right Lull and Porter style Shutter Hinge

    # 0 Right Lull and Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.

    Hinge Width when open - 6-7/16"

    Hinge throw from casing - 4-1/8"

    Hinge Height at mortise-3-1/2"

    These do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a  drill.

     

    0 right open rear

  • # 1 Left Lull and Porter style Shutter Hinges

    # 1 Left Lull and Porter style Shutter Hinges. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.

    Hinge Width when open - 5-1/2"

    Hinge throw from casing - 3-11/16"

    Hinge Height at mortise-3-3/16"

    These do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a  drill.

     1 left open rear

Title

Go to Top