Large Plain Oval Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 14″ wide and 8-1/4″ tall. The front measurement is 18-1/4″ wide and 12-3/8″ tall. The vent recesses into the foundation 3-3/8″ deep.
16 Inch Iron Head Bolt is most often used on a double door application and secures the stationary door at the top, it is highly recommended for use with a foot bolt (or bottom bolt) to prevent warping. The bolt measures 16-3/4″ tall and the rear plate measures 1-7/8″ wide by 6″ tall. The bolt tongue measures 3/4″ when activated, and is 5/8″ wide. The bolt comes with two different keepers, one used when the door is flush with it’s casing, and one used when the door is set deeper into its casing. It also comes with one stay used to keep the arm from being pulled from the surface of the door. It is important to note that in order to operate the bolt properly it must only be pulled up or down, never forward away from the surface of the door (this action would put stress on the weld that attaches the arm to the bolt).
9 Light marginal doors- Available in both 6'8" and 8'0" heights. These doors are made of Mahogany and feature beveled, tempered glass. These are sold as slabs only and do not come prehung. It is important to note that if you are ordering pairs of sidelights - each listing is for a single slab, so you will need to order two slabs to make a pair.
The following sizes are available:
36" x 80" x 1-3/4" (Currently out of stock)
32" x 80" x 1-3/4"
30" x 80" x 1-3/4"
18" x 80" x 1-3/4" (6 light sidelight- see photos)
14" x 80" x 1-3/4" (3 light sidelight- see photos)
36" x 96" x 1-3/4"
32" x 96" x 1-3/4"
18" x 96" x 1-3/4" (6 light sidelight)
36" door with 14" sidelights
30" doors with 18" sidelights
36" x 80" door
Solid Brass Ball Bearing Hinges - steeple finial in multiple sizes
These hinges are made from solid brass, polished to a high shine and lacquered to prevent immediate tarnishing. The ball bearing helps to prevent the solid brass hinge from wearing down when used on heavier doors. They are sold as pairs (two hinges per package) and come with screws.
Two sizes are available, 3-1/2" x 3-1/2" and 4"x 4". Both sizes feature five knuckles with two ball bearings. 3-1/2" hinges have three screw holes per side, while 4" hinges have four.
11-1/4″ Tall
25-1/2″ Wide
13″ Deep
This planter is made of cast aluminum. The planter comes without a finish, we suggest you paint it.
We cannot ship this item using UPS, it would have to be delivered using a freight company, please call us for a shipping quote 504 488 5524.
15 Inch Steel Strap Hinge includes hinge and pintal. These heavy steel hinges have no offset, but can be bent to accommodate most offsets. We suggest priming and painting these before installation. You may use these on the left or right shutter. This product can be installed using a drill.
The exact measurements of the hinge itself are 15-1/4" long, 1-1/2" wide at widest point, tapers to 3/4" at the end.
The pintal measures 3-3/8" tall, 1-1/2" wide, and projects 1" from the back of the plate to the center of the pintal itself.
12 Inch Steel Hook and Eye. Contains one hook and one eye. All components are made of steel and left unfinished.
Hook length from center of hook to center of hole that attaches hook to the back plate- 11-1/4″
Overall hook length- 12″
Back plate size- 1-1/2″ x 3-3/8″ (1-1/4″ deep)
Eye size- 1-1/2″ x 3-3/8″ (3/4″ deep)
We recommend you prime and paint these before installation. They do not come with screws. It is ok to use a drill when installing this product.
Brass Embossed Sash Lock can be used either with casement or double hung windows. With double hung sashes the moving part of the latch would mount to the bottom sash and the keeper would mount to the top sash. The back plate of the keeper measures 2-3/8" x 7/8" and is a total of 3/4" tall. The back plate of the moving part of the latch measures 2-3/8" x 1-1/8". The arm measures 3-1/4" x 1".
Iron Transom Latch can be used in conjunction with pivoting transom hinges and would mount on the bottom rail of the transom, with the strike plate being mortised to the bottom of the transom's jamb. The latch is operated by pulling up on the loop at the top. (one of our clients suggests mounting a hook to the top of a broom stick to avoid getting on a stool.) The latch measures 2-1/8" wide, 1-1/4" tall, and 5/8" deep (with the loop standing 1-3/8" deep). The strike plate measures 1-3/4" wide, 1-1/2" deep, and mortises 1-3/4" x 3/4"x 3/16" into the jamb. It is made out of cast iron and painted black.
Iron Parliament Hinge with Five and Three Quarter Inch Offset measures a total of 7-7/8″ wide and 2-7/8″ tall. It mortises into the door or jamb 1-1/16″ x 2-7/8″ and has a throw of 5-3/4″ when open. The pin on the hinge is removable making it function as either a right or left hand swing.
Medium Brass Door Bolts can be used for interior doors that require a locking function (ex. bathrooms or bedrooms) where the door is flush with the casing. This bolt measures 4-1/2″ long and 1-1/4″ wide, stands 1-1/2″ tall from the surface of the door, and throws 1-1/4″. The keeper measures 1-1/4″ long and 1-1/2″ tall.
Brass Flush Bolt is used with double door sets on the stationary panel and mortises into the margin of the door at the top and bottom of the door. Two bolts would be needed to properly hold the door in place and prevent warping. These specific bolts are used when you do not want to see hardware when your doors are closed, achieving a cleaner, more modern look. the bolt measures 3/4" wide, 8" tall and 1-3/8" deep. Each bolt comes with a strike plate measuring 3/4"deep and 1-3/8" wide.
The iron Victorian pull handle is made of cast iron and powder coated in a black finish. The back plate measures 18" x 3-1/2" at the tallest and widest points (3" wide at the narrowest point). the pull handle itself is 13-1/2" from tip of finial to tip of finial and projects 3-3/8" from the surface of the door. This pull would be impressive on a set of barn doors, on a double door, or used as a hand towel bar in your kitchen or bath.
Flat Panel with Shaker Profile Doors- Traditionally have flat panels (either plywood or cypress) with a square profile on the stiles and rails.
Flat T Panel With Shaker Profile
Flat Panel with Shaped Profile Doors- These are the most common of the T panel doors, panels are flat (either plywood or cypress) with a shaped profile on the stiles and rails.
Raised Panel Doors- The least common of the T panel styles, has cypress raised panels.
Raised T Panel
Antique T panel doors come in widths from 28″ wide to 34″ wide, although we do have some others in odd widths. The height starts around 76″, and up to 84″ normally we do have some in odd heights. The thickness ranges from 1″ to 1-1/2″.
Most of our doors are made of cypress. They are antique, used doors and will have holes, blemishes and other imperfections. We do offer refurbishment at an additional cost that depends on what needs to be done to the specific door.
57-1/2″ tall
21″ deep
8″ wide
This mailbox is made of cast aluminum. The mailbox comes without a finish, we suggest you paint it. This mailbox does not lock.
We cannot ship this item using UPS, it would have to be delivered using a freight company, please call us for a shipping quote 504 488 5524.
Solid Brass Rose Knobs and Rosettes Set. This set mimics the Victorian decadence and pattern. Cast out of solid brass and polished to a mirror finish, lacquered to prevent immediate tarnishing. It translates nicely when updating an older home while trying to maintain the small details that make an older home so appealing. The set comes with two rosettes, two knobs, a shaft that connects the two knobs with set screws, and two set screws. These will not work with predrilled doors, but can be customized below for all of your other needs.
The rosettes measure 2-3/8″ in diameter
The knobs measure 2-3/8″ in diameter and rise 2-3/4″ from the surface of the door
Solid Brass Jerome Door Knobs and Plates Set. Originally patented in 1909 by Russell and Erwin the “Jerome” pattern was used during much of the craftsman era. We have interpreted the original design into a lovely set of solid cast brass hardware. The set is composed of two back plates, two screw on knobs, a shaft that connects the two knobs by set screws, and four set screws. This set will work for predrilled doors, it can be made into “dummy knobs” (call for price). They do not come with any latch or locking device.
The plates measure 2-1/2″ x 9-1/8″
The Knobs are 2-1/4″ in diameter
The set projects 3″ from the face of the door
8 Inch Steel Hook and Eye. Contains one hook and one eye. All components are made of steel and left unfinished.
Hook length from center of hook to center of hole that attaches hook to the back plate- 7″
Overall hook length- 7-3/4″
Back plate size- 1-1/2″ x 3-3/8″ (1-1/4″ deep)
Eye size- 1-1/2″ x 3-3/8″ (3/4″ deep)
We recommend you prime and paint these before installation. They do not come with screws. It is ok to use a drill when installing this product.
Iron Casement Stay is made to secure casement windows in either a closed or open position. The Maximum throw is 10-1/2". These are meant for use in an outswing application only.
Three Inch Steeple Top Embossed Brass Hinges are sold in pairs of two. They feature a removable pin for ease of installation.
Small Brass Door Bolts can be used for interior doors that require a locking function (ex. bathrooms or bedrooms) where the door is flush with the casing. This bolt measures 3-3/4" long and 1-3/8" wide, stands 1-1/4" tall from the surface of the door, and throws 10/16". The keeper measures 7/8" long and 1-1/4" tall.
