Bolts, latches, locks, hinges, accessories and handles
Iron Parliament Hinge with Three Inch Offset measures a total of 5-1/8" wide and 2-7/8" tall. It mortises into the door or jamb 1" x 2-7/8" and has a throw of 3" when open. The pin on the hinge is removable making it function as either a right or left hand swing.
28 Inch Iron Head Bolt is most often used on a double door application and secures the stationary door at the top, it is highly recommended for use with a foot bolt (or bottom bolt) to prevent warping. The bolt measures 28-1/2" tall and the rear plate measures 1-15/16" wide by 6" tall. The bolt tongue measures 7/8" when activated, and is 3/4" wide. The bolt comes with two different keepers, one used when the door is flush with it's casing, and one used when the door is set deeper into its casing. It also comes with two stays used to keep the arm from being pulled from the surface of the door. It is important to note that in order to operate the bolt properly it must only be pulled up or down, never forward away from the surface of the door (this action would put stress on the weld that attaches the arm to the bolt).
Solid Brass Knob and Lever Set with Rosettes. This set mimics screen door and small French door knob and lever sets found in New Orleans. The set comes with one knob, one lever, one circular rosette, one oval rosette, a shaft that connects the knob to the lever with set screws, and two set screws. This set will not work on predrilled doors, nor can it be made into "dummy knobs". It does not come with any latching or locking device.
The knob measures 1-3/4" in diameter and rises 2-1/8" from the surface of the door
The lever measures 3" long 7/8" in diameter at shank and rises 2-1/2" from the surface of the door
The round rosette measures 1-3/4" in diameter
The oval rosette measures 1-3/4" x 1-3/8"
Iron Parliament Hinge with Four and Three Quarter Inch Offset measures a total of 7″ wide and 3-3/8″ tall. It mortises into the door or jamb 1-1/8″ x 3-3/8″ and has a throw of 4-3/4″ when open. The pin on the hinge is removable making it function as either a right or left hand swing.
Iron Parliament Hinge with Four and a Quarter Inch Offset measures a total of 6-3/8″ wide and 2-7/8″ tall. It mortises into the door or jamb 1″ x 2-7/8″ and has a throw of 4-1/4″ when open. The pin on the hinge is removable making it function as either a right or left hand swing.
Three and a Half Inch Steeple Top Embossed Brass Hinges are sold in pairs of two. They feature a removable pin for ease of installation.
Solid Brass Beaded Oval Knobs and Plates Set. This set mimics what would be found in some of the Creole homes in and around New Orleans. Cast out of solid brass and polished to a mirror finish, lacquered to prevent immediate tarnishing. It translates nicely when modernizing and updating an older home while trying to maintain the small details that make an older home so appealing. The set comes with two back plates, two knobs, a shaft that connects the two knobs with set screws, and two set screws. These will not work with predrilled doors, but can be made into “dummy knobs” (call for price). This set does not come with any locking or latching device.
The back plates measure 2-1/4″ x 7″ at their widest points
The knobs measure 1-5/8″ x 2-1/2″ at their widest points and rise 2-1/2″ from the surface of the door
Embossed Iron Steeple Top Hinges 4" x 4" are sold in pairs of two (one hinge shown in images). These are made of cast iron and painted semi-gloss black. The pin is removable for ease of hanging. There is embossing on the face of the hinge and the reveal on the side of the hinge. The pattern of the embossing is in a linear Eastlake Victorian style.
Solid Brass Broken Leaf Door Knobs and Plates Set. Originally patented in 1887 by Lockwood Manufacturing Company, the “Broken Leaf” pattern was widely used at the end of the Victorian era, a style that has come to be known as Eastlake. We have interpreted the original design into a lovely set of solid cast brass hardware. The set is composed of two back plates, two slip on knobs, a shaft that connects the two knobs by set screws, and two set screws. This set will not work for predrilled doors, nor can it be made into “dummy knobs”. They do not come with any latch or locking device.
The plates measure 1-1/2″ x 5-5/16″
The Knobs are 2-1/4″ in diameter
The set projects 2-1/2″ from the face of the door
Solid Brass Ball Bearing Hinges - ball finial in multiple sizes
These hinges are made from solid brass, polished to a high shine and lacquered to prevent immediate tarnishing. The ball bearing helps to prevent the solid brass hinge from wearing down when used on heavier doors. They are sold as pairs (two hinges per package) and come with screws.
Two sizes are available, 3-1/2" x 3-1/2" and 4"x 4". Both sizes feature five knuckles with two ball bearings. 3-1/2" hinges have three screw holes per side, while 4" hinges have four.
Large Brass Door Bolts can be used for interior doors that require a locking function (ex. bathrooms or bedrooms) where the door is flush with the casing. This bolt measures 6-1/8″ long and 1-1/2″ wide, stands 1-1/2″ tall from the surface of the door, and throws 1-5/8″. The keeper measures 1-1/4″ long and 1-1/2″ tall.
8 Inch Iron Foot Bolt is most often used on a double door application and secures the stationary door at the bottom, it is highly recommended for use with a head bolt (or top bolt) to prevent warping. The bolt measures 9-1/4″ tall and the rear plate measures 1-7/8″ wide by 5-1/2″ tall. The bolt tongue measures 1-1/16″ when activated, and is 3/4″ wide. The bolt comes with two different keepers, one used when the threshold extends well past the door and can be mortised into, and one used when the threshold does not extend much past the door. It is important to note that in order to operate the bolt properly it must only be pulled up or down with your hand, never forward away from the surface of the door, or operated with your foot (this action would put stress on the weld that attaches the arm to the bolt).
Embossed kick bolts- available in two sizes and two finishes
The embossed kick bolts in the brass finish are made from solid, cast brass. The embossed kick bolts in the powder coated black are made from cast iron. These embossed kick bolts are designed to go at the bottom of the stationary door, shutter, or window when there are pairs of doors, shutters, or windows. We highly recommend you use these with a chain bolt (or top bolt) to prevent warping of your door.
The small bolts have the following measurements:
The bolt body measures 1-7/8 ” wide and 5-1/16″ tall, the tongue sticks out 1/2″ from the body of the latch when activated. The bolt is designed to be operated with your foot, the large button at the top activates it and the small button on the face deactivates it. The bolt comes with two strike plates- one measuring 1-7/8″wide and 2-3/8″ deep, and one measuring 2″ wide and 7/8″ deep.
The large bolts have the following measurements:
The bolt body measures 2 ” wide and 7-1/16″ tall, the tongue sticks out 3/4″ from the body of the latch when activated. The bolt is designed to be operated with your foot, the large button at the top activates it and the small button on the face deactivates it. The bolt comes with two strike plates- one measuring 1-7/8″wide and 2-3/8″ deep, and one measuring 2″ wide and 7/8″ deep.
Solid Brass Ossa Door Plates and Knobs Set. Originally patented in 19101 by Russell and Erwin the “Ossa” pattern was used at the through the Craftsman period. We have interpreted the original design into a lovely set of solid cast brass hardware. The set is composed of two back plates, two slip on knobs, a shaft that connects the two knobs by set screws, and two set screws. This set will work for predrilled doors, but can not be made into “dummy knobs”. They do not come with any latch or locking device.
The plates measure 2-9/16″ x 8-5/16″
The Knobs are 2-1/4″ in diameter
The set projects 2-1/2″ from the face of the door
16 Inch Iron Head Bolt is most often used on a double door application and secures the stationary door at the top, it is highly recommended for use with a foot bolt (or bottom bolt) to prevent warping. The bolt measures 16-3/4″ tall and the rear plate measures 1-7/8″ wide by 6″ tall. The bolt tongue measures 3/4″ when activated, and is 5/8″ wide. The bolt comes with two different keepers, one used when the door is flush with it’s casing, and one used when the door is set deeper into its casing. It also comes with one stay used to keep the arm from being pulled from the surface of the door. It is important to note that in order to operate the bolt properly it must only be pulled up or down, never forward away from the surface of the door (this action would put stress on the weld that attaches the arm to the bolt).
Solid Brass Ball Bearing Hinges - steeple finial in multiple sizes
These hinges are made from solid brass, polished to a high shine and lacquered to prevent immediate tarnishing. The ball bearing helps to prevent the solid brass hinge from wearing down when used on heavier doors. They are sold as pairs (two hinges per package) and come with screws.
Two sizes are available, 3-1/2" x 3-1/2" and 4"x 4". Both sizes feature five knuckles with two ball bearings. 3-1/2" hinges have three screw holes per side, while 4" hinges have four.
Iron Parliament Hinge with Five and Three Quarter Inch Offset measures a total of 7-7/8″ wide and 2-7/8″ tall. It mortises into the door or jamb 1-1/16″ x 2-7/8″ and has a throw of 5-3/4″ when open. The pin on the hinge is removable making it function as either a right or left hand swing.
Medium Brass Door Bolts can be used for interior doors that require a locking function (ex. bathrooms or bedrooms) where the door is flush with the casing. This bolt measures 4-1/2″ long and 1-1/4″ wide, stands 1-1/2″ tall from the surface of the door, and throws 1-1/4″. The keeper measures 1-1/4″ long and 1-1/2″ tall.
Brass Flush Bolt is used with double door sets on the stationary panel and mortises into the margin of the door at the top and bottom of the door. Two bolts would be needed to properly hold the door in place and prevent warping. These specific bolts are used when you do not want to see hardware when your doors are closed, achieving a cleaner, more modern look. the bolt measures 3/4" wide, 8" tall and 1-3/8" deep. Each bolt comes with a strike plate measuring 3/4"deep and 1-3/8" wide.
The iron Victorian pull handle is made of cast iron and powder coated in a black finish. The back plate measures 18" x 3-1/2" at the tallest and widest points (3" wide at the narrowest point). the pull handle itself is 13-1/2" from tip of finial to tip of finial and projects 3-3/8" from the surface of the door. This pull would be impressive on a set of barn doors, on a double door, or used as a hand towel bar in your kitchen or bath.
Solid Brass Rose Knobs and Rosettes Set. This set mimics the Victorian decadence and pattern. Cast out of solid brass and polished to a mirror finish, lacquered to prevent immediate tarnishing. It translates nicely when updating an older home while trying to maintain the small details that make an older home so appealing. The set comes with two rosettes, two knobs, a shaft that connects the two knobs with set screws, and two set screws. These will not work with predrilled doors, but can be customized below for all of your other needs.
The rosettes measure 2-3/8″ in diameter
The knobs measure 2-3/8″ in diameter and rise 2-3/4″ from the surface of the door
