(504) 488-5524 or (504) 822-8200|riccaarch@yahoo.com
FacebookYouTube

Hardware

Home/Hardware
  • Out of stock

    Brass Pivot Hinge For Transoms

    $ 7.65

    Brass Pivot Hinge for Transoms

    Brass pivot hinge for transoms include one hinge- the pin side and the receiver side. You will need to order two in order to do one sash. These are solid Brass with a lacquered finish.

    The pin side has the following measurements:

    Center to center of screw hole 1-1/8″

    Face of Hinge -2-3/8″ tall, 1″ wide, and mortises 1/8″ into the face of the transom.

    Side of hinge- 3/4″ tall, 1- 1/16″ wide, 3/16″ thick, center of pin to edge 7/8″, pin diameter 7/16″, pin length 15/16″

    The receiver side has the following measurements:

    Center to center of screw hole 1-1/4″

    Diameter of center hole 3/8″

    1-15/16″ tall, 7/8″ wide and 1/4″ deep

    Brass Pivot Hinge

    Details

  • # 3 Right Lull and Porter style Shutter Hinge

    $ 3.20

    # 3 Right Lull and Porter Style Shutter Hinge

    #3 Right Lull & Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.

    Hinge Width when open - 3-1/4"

    Hinge throw from casing - 1-3/8"

    Hinge height at mortise -2-9/16"

    These do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.

    3 right open rear

    Add to cart Details

  • 6 Inch Shutter Pull

    $ 10.00

    6 Inch Shutter Pull

    6 Inch Shutter Pull. These pulls are usually located on the inner stile of a shutter in order to close it from inside of your window. The handle is done in a bail style and folds away to a 1/4" profile when not in use. These do not come with screws. The rear plate is steel and the handle is cast iron. They come powder coated in a matte black finish.

    The Shutter Pulls have the following dimensions:

    Height- 6-1/4"

    Width- 1"

    Center to Center of outer Screw Holes- 5-1/2"

    Handle height- 3-7/8"

    Handle Depth- 1-1/4"

    6 inch shutter pull

    Add to cart Details

  • # 3 Left Lull and Porter style Shutter Hinge

    $ 3.20

    # 3 Left Lull and Porter style Shutter Hinge

    # 3 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.

    Hinge Width when open – 3-1/4″

    Hinge throw from casing – 1-1/2″

    Hinge Height at mortise- 2-9/16"

    They do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.

    3 left open rear

    Add to cart Details

  • Shutter Catches

    $ 4.00

    Shutter Catches

    Shutter Catches. These typically mount at the bottom of the shutter and latch to the sill of the window. These can only be used when you can open your window and access the rear of your shutters. The set comes with one latch an one catch, you will need two sets for each pair of shutters. Both pieces are made of cast iron. We recommend you prime and paint these before installation and screw them in with a screwdriver by hand, not with a drill. These do not come with screws.

     cincinatti catch

    Add to cart Details
  • 8 inch Shutter Slide

    8 Inch Shutter Slide Bolt

    $ 20.00

    8 Inch Shutter Slide Bolt

    8 Inch Shutter Slide Bolt. These slide shutter bolts are meant to mount to a pair of shutters in the space between the shutter and the window and function to fasten the shutters during a storm. The back plate, keeper, and straps are made of steel and the bolt itself is made of cast iron. They are powder coated in a glossy black finish.
    • They do not come with screws.
    • The back plate at the rear of the bolt measures 6-1/16″ x 1-11/16″
    • The bolt measures 7-51/16″ x 7/8″
    • The handle of the bolt projects 1-1/16″ from the rear
    • The keeper measures 2-1/4″ x 1-3/4″
    • The bolt throws 2-5/8″ out from the rear plate

    Ricca’s Architectural Sales

    511 North Solomon Street, New Orleans, LA 70119 (504) 488 – 5524 or (504) 822-8200 Fax: (504) 488 – 5662, Email: riccaarch@yahoo.com
    Business Hours:
    Tuesday – Friday 9 am – 5 pm Saturday – 9 am – 4 pm

    8 inch shutter slide bolt

    Add to cart Details

  • Iron Parliament Hinge with Three Inch Offset

    $ 9.50

    Iron Parliament Hinge with Three Inch Offset

    Iron Parliament Hinge with Three Inch Offset measures a total of 5-1/8" wide and 2-7/8" tall. It mortises into the door or jamb 1" x 2-7/8" and has a throw of 3" when open. The pin on the hinge is removable making it function as either a right or left hand swing.

    five and an eigth parlament hinge

    Add to cart Details

  • # 2 1/2 Right Lull and Porter style Shutter Hinge

    $ 3.20

    # 2  1/2 Right lull and Porter style Shutter Hinge

    # 2  1/2 Right Lull and Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.

    Hinge Width when open - 3-7/8"

    Hinge Throw from casing - 2-3/16"

    Hinge Height at mortise- 2-7/16"

    They do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a  drill.

    two and a half Right open rear

    Add to cart Details

  • # 2 1/2 Left Lull and Porter style Shutter Hinge

    $ 3.20

    #  2 1/2 Left Lull and Porter style Shutter Hinge

    # 2 1/2 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.

    Hinge Width when open - 3-13/16"

    Hinge throw from casing - 2-1/16"

    Hinge Height at mortise - 2-9/16"

    They do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a  drill.

    two and a half left open rear

    Add to cart Details

  • 6 Inch Shutter Slide Bolt

    $ 15.00

    6 Inch Shutter Slide Bolt

    6 Inch Shutter Slide Bolt. These slide bolts are meant to mount to a pair of shutters in the space between the shutter and the window and function to fasten the shutters during a storm. The back plate, keeper, and straps are made of steel and the bolt itself is made of cast iron. They are powder coated in a glossy black finish.

    They do not come with screws.

    The back plate at the rear of the bolt measures 5" x 1-3/4"

    The bolt measures 6-11/16" x 13/16"

    The handle of the bolt projects 1-1/16" from the rear

    The keeper measures 2-1/4" x 1-3/4"

    The bolt throws 1-15/16" out from the rear plate

    6 inch shutter slide bolt

    Add to cart Details
  • Out of stock

    Brass Sash Pulley

    $ 20.00

    Brass Sash Pulley

    Brass Sash Pulley measures 4-3/4″ x 1-1/4″ at the face, it mortises 2-1/4″ deep into the jamb of the window.

    Brass Window Pulley

    Details

  • Brass Through Shutter Latch

    $ 21.50

    Brass Through Shutter Latch

    Brass Through Shutter Latch. These solid brass shutter latches are polished and lacquered to prevent immediate tarnish. They are intended to be mortised through the bottom of the shutter and hook to their keeper mounted on the window sill. When open they connect to a keeper mounted on the exterior of the home. These latches take the place of both dogs and slide bolts. These latches are meant for use on shutters 1-3/8" thick or less.  Each kit includes the latch, a plate for the rear of the shutter, a keeper for the sill, and a keeper for the wall. One kit will do a single shutter, you will need two kits for each window.

    The latch itself (the part that goes through the shutter) measures 2-3/8" at the top and 1-15/16" at the bottom

    The pull (the piece that you would operate) measures-1-1/4" tall and projects out 2" at the most (latch is 1-3/8" from the plate)

    The plate connected to the latch is 2" wide and 1-1/2" tall

    The plate that goes on the rear measures 1-3/8" tall and 1-1/2" wide

    The sill keeper (looks like bottle opener) is 1-3/4" deep and 1" wide

    The wall keeper (L shaped) is 1-1/16" tall, 15/16" wide and projects 1" from the wall

    Brass Through Shutter Latch Kit

    Add to cart Details

  • # 0 Right Lull and Porter style Shutter Hinge

    $ 5.15

    # 0 Right Lull and Porter style Shutter Hinge

    # 0 Right Lull and Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.

    Hinge Width when open - 6-7/16"

    Hinge throw from casing - 4-1/8"

    Hinge Height at mortise-3-1/2"

    These do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a  drill.

     

    0 right open rear

    Add to cart Details
  • Out of stock

    Brass Knuckle Sash Lock

    $ 10.50

    Brass Knuckle Sash Lock

    Brass Knuckle Sash Lock is meant for use with double hung windows. The lock comes with two pieces, the latching part, and the receiver which gets overlapped. These were found on most double hung sashes in New Orleans that predated the 1910's. The base of the latching part measures 1-7/8" x 13/16". The base of the receiver measures 1-7/8" x  3/4". It is made of solid brass.

    Brass Knuckle Sash Lock

    Details

  • # 1 1/2 Left Lull and Porter style Shutter Hinge

    $ 3.75

    # 1 1/2 Left Lull and Porter style Shutter Hinge

    # 1 1/2 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.

    Hinge Width when open - 5-1/8"

    Hinge throw from casing - 3-1/4"

    Hinge Height at mortise- 3"

    They do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.

    one and a half left open rear

    Add to cart Details

  • Iron Pivot Hinge For Transoms

    $ 5.50

    Iron Pivot Hinge for Transoms

    Iron pivot hinge for transoms include one hinge- the pin side and the receiver side. You will need to order two in order to do one sash. These are made of cast iron and left unfinished.

    The pin side has the following measurements:

    Center to center of screw hole 1-1/2"

    Face of Hinge -2-3/8" tall, 7/8" wide, and mortises 1/8" into the face of the transom.

    Side of hinge- 5/8" tall, 7/8" wide, 1/8" thick, center of pin to edge 3/4", pin diameter 3/8", pin length 11/16"

    The receiver side has the following measurements:

    Center to center of screw hole 1-1/8"

    Diameter of center hole 7/16"

    1-11/16" tall, 3/4" wide and 1/8" deep

    Iron Pivot Hinges

    Add to cart Details

  • # 1 1/2 Right Lull and Porter style Shutter Hinge

    $ 3.75

    # 1 1/2 Right Lull and Porter style Shutter Hinge

    # 1 1/2 Right Lull and Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.

    Hinge Width when open - 5"

    Hinge throw from casing - 3-1/4"

    Hinge Height at mortise - 2-7/8"

    They do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.

    one and a half right open rear

    Add to cart Details

  • # 0 Left Lull and Porter style Shutter Hinge

    $ 5.15

    # 0 Left Lull and Porter style Shutter Hinge

    # 0 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.

    Hinge Width when open - 6-7/16"

    Hinge throw from casing - 4-1/8"

    Hinge Height at mortise- 3-1/2"

    These do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a  drill.

    0 left open rear

    Add to cart Details
  • Out of stock

    Brass Oval Beaded Sash Lift

    $ 9.00

    Brass Oval Beaded Sash Lift

    Brass Oval Beaded Sash Lift measures 4" x 2" and mortises into the sash 3/8" deep at 2-3/4" x 1-1/4".

    Oval Beaded Sash Lift

    Details
  • 12in Shutter Slide

    12 Inch Shutter Slide Bolt

    $ 30.00

    12 Inch Shutter Slide Bolt

    12 Inch Shutter Slide Bolt. These slide bolts are meant to mount to a pair of shutters in the space between the shutter and the window and function to fasten the shutters during a storm. The back plate, keeper, and straps are made of steel and the bolt itself is made of cast iron. They are powder coated in a glossy black finish.

    They do not come with screws.

    The back plate at the rear of the bolt measures 8-13/16″ x 2-1/16″

    The bolt measures 8-3/16″ x 7/8″

    The handle of the bolt projects 3/4″ from the rear

    The keeper measures 3-13/16″ x 2-1/16″

    The bolt throws 3-3/4″ out from the rear plate

    12 Inch Shutter Slide Bolt12in Shutter Slide

    Add to cart Details

  • # 1 Left Lull and Porter style Shutter Hinge

    $ 3.75

    # 1 Left Lull and Porter style Shutter Hinges

    # 1 Left Lull and Porter style Shutter Hinges. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.

    Hinge Width when open - 5-1/2"

    Hinge throw from casing - 3-11/16"

    Hinge Height at mortise-3-3/16"

    These do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a  drill.

     1 left open rear

    Add to cart Details
  • Out of stock

    Brass Transom Latch

    $ 12.50

    Brass Transom Latch

    Brass Transom Latch can be used in conjunction with pivoting transom hinges and would mount on the bottom rail of the transom, with the strike plate being mortised to the bottom of the transom's jamb. The latch is operated by pulling up on the loop at the top. (one of our clients suggests mounting a hook to the top of a broom stick to avoid getting on a stool.) The latch measures 2-1/8" wide, 1-1/4" tall, and 5/8" deep (with the loop standing 1-3/8" deep). The strike plate measures 1-3/4" wide, 1-1/2" deep, and mortises 1-3/4" x 3/4"x 3/16" into the jamb. It is made out of solid brass.

    Brass Transom Latch

    Details

  • # 2 Right Lull and Porter style Shutter Hinge

    $ 3.70

    # 2 Right Lull and Porter style Shutter Hinge

    # 2 Right Lull and Porter style Shutter Hinge. Right shutter hinge mounts on the left side of the window when looking at the window from outside of your home.

    Hinge Width when open - 4-7/16"

    Hinge throw from casing - 2-1/2"

    Hinge Height at mortise-2-7/8"

    They do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.

     2 right open rear

    Add to cart Details

  • # 2 Left Lull and Porter style Shutter Hinge

    $ 3.70

    # 2 Left Lull and Porter style Shutter Hinge

    # 2 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.

    Hinge Width when open - 4-7/16"

    Hinge throw from casing - 2-5/8"

    Hinge Height at mortise- 2-15/16"

    They do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.

    2 left open rear

    Add to cart Details

  • 6 Inch Cast Iron Hook and Eye

    $ 14.00

    6 Inch Cast Iron Hook and Eye

    6 Inch Cast Iron Hook and Eye. Contains one hook and one eye. All components are made of cast iron and powder coated in a matte black finish.

    Hook length from center of hook to center of hole that attaches hook to the back plate- 5-3/8″

    Overall hook length- 6″

    Back plate size- 1-3/4″ x 1-3/8″  (1-1/4″ deep)

    Eye size- 1-3/4″ x 1-3/8″ (1-1/4″ deep)

    6 inch cast iron hook and eye

    Add to cart Details

  • Clark Tip Left Shutter Hinge

    $ 5.80

    Clark Tip Left Shutter Hinge

    Clark Tip Left Shutter Hinge. For a face mount application when mortising a hinge is not an option. Left Hinges mount on the right side of the window when looking at the window from the exterior. These work well with use on brick homes or homes with wood casing. They are made from cast iron. We suggest you prime and paint these before installation, and screw them in by hand, not with a drill.

    These do not come with screws.

    Portion of hinge that mounts to the face of your casing- 1-1/2" x 2-1/2"

    Portion of hinge that mounts on the face of the shutter- 1-1/2" x 2-1/2"

    Throw provided by hinge when open- 3-1/4"

    Clarke tip left profile

    Add to cart Details

  • Traditional Brass Sash Lock

    $ 10.00

    Traditional Brass Sash Lock

    Traditional Brass Sash Lock is meant for use with double hung style windows.  The base of the latch measures 2-5/8" x 7/8" and the base of the keeper measures 2-1/2" x 5/8".

    Brass Traditional Sash Lock

    Add to cart Details
  • Out of stock

    Embossed Brass Pull

    $ 8.50

    Embossed Brass Pull

    Embossed Brass Pull measures 6-1/2" tall, 1-1/4" wide, and 1-1/4" deep.

    R-28

    Details

  • 4 Inch Cast Iron Hook and Eye with Diamond Shaped Backing

    $ 12.00

    4 Inch Cast Iron Hook and Eye with Diamond Shaped Backing

    4 Inch Cast Iron Hook and Eye with Diamond Shaped Backing. Contains one hook and one eye. All components are made of cast iron and powder coated in a matte black finish.

    Hook length from center of hook to center of hole that attaches hook to the back plate-4″

    Overall hook length- 4-1/2″

    Back plate size- 2″ x 1-3/8″  (7/8″ deep)

    Eye size- 2″ x 1-3/8″ (7/8″ deep)

    4 inch cast iron hook and eye diamond back

    Add to cart Details

  • # 1 Right Lull and Porter style Shutter Hinge

    $ 3.75

    # 1 Right Lull and Porter style Shutter Hinge

    # 1 Right Lull and Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.

    Hinge Width when open - 5 -1/2"

    Hinge throw from casing - 3-5/8"

    Hinge Height at Mortise- 3-1/8"

    They do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.

    1 right open rear

    Add to cart Details

  • Brass Victorian Sash Lift

    $ 12.00

    Brass Victorian Sash Lift

    Brass Victorian Sash Lift measures 5-1/4" x 1-3/4" and mortises 3/8" deep at 2-3/4" x 1-1/8".

    Victorian Sash Lift

    Add to cart Details

  • 28 Inch Iron Head Bolt

    $ 45.00

    28 Inch Iron Head Bolt

    28 Inch Iron Head Bolt is most often used on a double door application and secures the stationary door at the top, it is highly recommended for use with a foot bolt (or bottom bolt) to prevent warping. The bolt measures 28-1/2" tall and the rear plate measures 1-15/16" wide by 6" tall. The bolt tongue measures 7/8" when activated, and is 3/4" wide. The bolt comes with two different keepers, one used when the door is flush with it's casing, and one used when the door is set deeper into its casing. It also comes with two stays used to keep the arm from being pulled from the surface of the door. It is important to note that in order to operate the bolt properly it must only be pulled up or down, never forward away from the surface of the door (this action would put stress on the weld that attaches the arm to the bolt).

    28 inch iron head bolt

    Add to cart Details

  • 4 Inch Cast Iron Hook and Eye with Round Backing

    $ 12.00

    4 Inch Cast Iron Hook and Eye with Round Backing

    4 Inch Cast Iron Hook and Eye with Round Backing. Contains one hook and one eye. All components are made of cast iron and powder coated in a matte black finish.

    Hook length from center of hook to center of hole that attaches hook to the back plate- 3-1/2"

    Overall hook length- 4"

    Back plate size- 1-3/4" x 1-3/8"  (1-1/4" deep)

    Eye size- 1-3/4" x 1-3/8" (1-1/4" deep)

    4 inch cast iron hook and eye round back

    Add to cart Details

  • Clark Tip Right Shutter Hinge

    $ 5.80

    Clark Tip Right Shutter Hinge

    Clark Tip Right Shutter Hinge. For a face mount application when mortising a hinge is not an option. Right hinges mount on the left side of the window when looking at the window from the exterior. These work well with use on brick homes or homes with wood casing. They are made from cast iron. We suggest you prime and paint these before installation, and screw them in by hand, not with a drill.

    These do not come with screws.

    Portion of hinge that mounts to the face of your casing- 1-1/2" x 2-1/2"

    Portion of hinge that mounts on the face of the shutter- 1-1/2" x 2-1/2"

    Throw provided by hinge when open- 3-1/4"

    clark tip right profile

    Add to cart Details

  • Solid Brass Knob and Lever Set with Rosettes

    $ 41.00

    Solid Brass Knob and Lever Set With Rosettes

    Solid Brass Knob and Lever Set with Rosettes. This set mimics screen door and small French door knob and lever sets found in New Orleans. The set comes with one knob, one lever, one circular rosette, one oval rosette, a shaft that connects the knob to the lever with set screws, and two set screws. This set will not work on predrilled doors, nor can it be made into "dummy knobs". It does not come with any latching or locking device.

    The knob measures 1-3/4" in diameter and rises 2-1/8" from the surface of the door

    The lever measures 3" long 7/8" in diameter at shank and rises 2-1/2" from the surface of the door

    The round rosette measures 1-3/4" in diameter

    The oval rosette measures 1-3/4" x 1-3/8"

    PA14

    Add to cart Details

  • Iron Parliament Hinge with Four and Three Quarter Inch Offset

    $ 9.75

    Iron Parliament Hinge with Four and Three Quarter Inch Offset

    Iron Parliament Hinge with Four and Three Quarter Inch Offset measures a total of 7″ wide and 3-3/8″ tall. It mortises into the door or jamb 1-1/8″ x 3-3/8″ and has a throw of 4-3/4″ when open. The pin on the hinge is removable making it function as either a right or left hand swing.

    seven inch parlament hinge

    Add to cart Details
  • 9 inch foot bolt

    9 Inch Brass Foot Bolt

    $ 45.00
    Add to cart Details

  • Iron Parliament Hinge with Four and a Quarter Inch Offset

    $ 9.50

    Iron Parliament Hinge with Four and a Quarter Inch Offset

    Iron Parliament Hinge with Four and a Quarter Inch Offset measures a total of 6-3/8″ wide and 2-7/8″ tall. It mortises into the door or jamb 1″ x 2-7/8″ and has a throw of 4-1/4″ when open. The pin on the hinge is removable making it function as either a right or left hand swing.

    six and three eigths parlament hinge

    Add to cart Details
  • Out of stock

    Iron Arched Bin Pull

    $ 8.50

    Iron Arched Bin Pull

    Iron Arched Bin Pull measures 4" wide, 1-5/8" tall, and 1/2" deep. They are powder-coated black.

    R Bin Pull

    Details
  • Out of stock

    Three and a Half Inch Steeple Top Embossed Brass Hinges

    $ 38.00

    Three and a Half Inch Steeple Top Embossed Brass Hinges

    Three and a Half Inch Steeple Top Embossed Brass Hinges are sold in pairs of two. They feature a removable pin for ease of installation.

    three and a half inch embossed brass hinge

    Details

  • Brass Eastlake Pull

    $ 9.50

    Brass Eastlake Pull

    Brass Eastlake Pull measures 4-1/4" tall, 1-5/8" wide, and 1" deep.

    Eastlake Pull

    Add to cart Details
  • Out of stock

    Solid Brass Beaded Oval Knobs and Plates Set

    $ 45.00

    Solid Brass Beaded Oval Knobs and Plates Set

    Solid Brass Beaded Oval Knobs and Plates Set. This set mimics what would be found in some of the Creole homes in and around New Orleans. Cast out of solid brass and polished to a mirror finish, lacquered to prevent immediate tarnishing. It translates nicely when modernizing and updating an older home while trying to maintain the small details that make an older home so appealing. The set comes with two back plates, two knobs, a shaft that connects the two knobs with set screws, and two set screws. These will not work with predrilled doors, but can be made into “dummy knobs” (call for price). This set does not come with any locking or latching device.

    The back plates measure 2-1/4″ x 7″ at their widest points

    The knobs measure 1-5/8″ x 2-1/2″ at their widest points and rise 2-1/2″ from the surface of the door

    VB1197B
    Details

  • Embossed Iron Steeple Top Hinges 4″ x 4″

    $ 24.00

    Embossed Iron Steeple Top Hinges 4" x 4"

    Embossed Iron Steeple Top Hinges 4" x 4" are sold in pairs of two (one hinge shown in images). These are made of cast iron and painted semi-gloss black. The pin is removable for ease of hanging. There is embossing on the face of the hinge and the reveal on the side of the hinge. The pattern of the embossing is in a linear Eastlake Victorian style.four by four embossed steeple 2 closed

    four by four embossed steeple 2 open

    Add to cart Details

  • Iron Fleur de Lis Door Knocker

    $ 22.00

    fleur-de-lis-door-knocker

    Iron Fleur de Lis Door Knocker

    Iron Fleur de Lis Door Knocker measures 3-7/8" wide and 5-1/4" tall overall. The strike plate measures 1-3/4" in diameter. The knocker and  strike plate attach to your door with machine style bolts, that extend through the rear of your door.

     

     
    Add to cart Details
  • Out of stock

    Solid Brass Broken Leaf Knobs and Plates Set

    $ 46.00

    Solid Brass Broken Leaf Knobs and Plates Set

    Solid Brass Broken Leaf Door Knobs and Plates Set. Originally patented in 1887 by Lockwood Manufacturing Company, the “Broken Leaf” pattern was widely used at the end of the Victorian era, a style that has come to be known as Eastlake. We have interpreted the original design into a lovely set of solid cast brass hardware. The set is composed of two back plates, two slip on knobs, a shaft that connects the two knobs by set screws, and two set screws. This set will not work for predrilled doors, nor can it be made into “dummy knobs”. They do not come with any latch or locking device.

    The plates measure 1-1/2″ x 5-5/16″

    The Knobs are 2-1/4″ in diameter

    The set projects 2-1/2″ from the face of the door

    R108

    Details

  • 8 Inch Cast Iron Hook and Eye

    $ 16.00

    8 Inch Cast Iron Hook and Eye

    8 Inch Cast Iron Hook and Eye. Contains one hook and one eye. All components are made of cast iron and powder coated in a matte black finish.

    Hook length from center of hook to center of hole that attaches hook to the back plate- 7-7/16″

    Overall hook length- 8″

    Back plate size- 1-3/4″ x 1-3/8″  (1-1/4″ deep)

    Eye size- 1-3/4″ x 1-3/8″ (1-1/4″ deep)

    8 inch cast iron hook and eye

    Add to cart Details

  • Solid Brass Ball Bearing Hinges – ball finial in multiple sizes

    $ 38.00 – $ 48.00

    Solid Brass Ball Bearing Hinges - ball finial in multiple sizes

    Solid Brass Ball Bearing Hinges - ball finial in multiple sizes

    These hinges are made from solid brass, polished to a high shine and lacquered to prevent immediate tarnishing. The ball bearing helps to prevent the solid brass hinge from wearing down when used on heavier doors. They are sold as pairs (two hinges per package) and come with screws.

    Two sizes are available, 3-1/2" x 3-1/2" and 4"x 4". Both sizes feature five knuckles with two ball bearings. 3-1/2" hinges have three screw holes per side, while 4" hinges have four.

    Select options Details
  • Out of stock

    12 Inch Steel Strap Hinge

    $ 20.00

    12 Inch Steel Strap Hinge

    12 Inch Steel Strap Hinge includes hinge and pintal. These heavy steel hinges have no offset, but can be bent to accommodate most offsets. We suggest priming and painting these before installation. You may use these on the left or right shutter. This product can be installed using a drill.

    The exact measurements of the hinge itself are 12-1/2" long,  1-1/2" wide at widest point, tapers to 3/4" at the end.

    The pintal measures 3-3/8" tall, 1-1/2" wide, and projects 1" from the back of the plate to the center of the pintal itself.

    12 inch steel Strap hinge

    Details

Title

Go to Top