Shop

Home/Shop

Any size, any shape, any style, any color, we may have it in stock and if we don’t we may be able to get it made for you!

Please call us for a price inquiry on anything that you see. Ricca’s Phone# 504 – 488 – 5524

  • Small Soffit Vent

    Small Soffit Vent measures 11-5/8" in diameter. They are made of cast aluminum, and sold unfinished. These can be used for venting the attic from your soffit, or look great as a decorative piece on a wooden gate.

    small soffit vent

  • Out of stock

    Brass Pivot Hinge for Transoms

    Brass pivot hinge for transoms include one hinge- the pin side and the receiver side. You will need to order two in order to do one sash. These are solid Brass with a lacquered finish.

    The pin side has the following measurements:

    Center to center of screw hole 1-1/8″

    Face of Hinge -2-3/8″ tall, 1″ wide, and mortises 1/8″ into the face of the transom.

    Side of hinge- 3/4″ tall, 1- 1/16″ wide, 3/16″ thick, center of pin to edge 7/8″, pin diameter 7/16″, pin length 15/16″

    The receiver side has the following measurements:

    Center to center of screw hole 1-1/4″

    Diameter of center hole 3/8″

    1-15/16″ tall, 7/8″ wide and 1/4″ deep

    Brass Pivot Hinge

  • # 3 Right Lull and Porter Style Shutter Hinge

    #3 Right Lull & Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.

    Hinge Width when open - 3-1/4"

    Hinge throw from casing - 1-3/8"

    Hinge height at mortise -2-9/16"

    These do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.

    3 right open rear

  • Flat Victorian Foundation Vent

    Flat Victorian Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally are screwed to the foundation. The measurement is 21-3/8″ wide and 13-5/8″ tall. The vent does not recess.

    Flat Foundation

  • 6 Inch Shutter Pull

    6 Inch Shutter Pull. These pulls are usually located on the inner stile of a shutter in order to close it from inside of your window. The handle is done in a bail style and folds away to a 1/4" profile when not in use. These do not come with screws. The rear plate is steel and the handle is cast iron. They come powder coated in a matte black finish.

    The Shutter Pulls have the following dimensions:

    Height- 6-1/4"

    Width- 1"

    Center to Center of outer Screw Holes- 5-1/2"

    Handle height- 3-7/8"

    Handle Depth- 1-1/4"

    6 inch shutter pull

  • Large Soffit Vent

    Large Soffit Vent measures 17-1/16" in diameter. They are made of cast aluminum, and sold unfinished. These can be used for venting the attic from your soffit, or look great as a decorative piece on a wooden gate.

    large soffit vent

  • # 3 Left Lull and Porter style Shutter Hinge

    # 3 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.

    Hinge Width when open – 3-1/4″

    Hinge throw from casing – 1-1/2″

    Hinge Height at mortise- 2-9/16"

    They do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.

    3 left open rear

  • Out of stock

    Medium Soffit Vent

    Medium Soffit Vent measures 13-1/16" in diameter. They are made of cast aluminum, and sold unfinished. These can be used for venting the attic from your soffit, or look great as a decorative piece on a wooden gate, or even covers for can lighting on your front porch.

    medium soffit

  • Shutter Catches

    Shutter Catches. These typically mount at the bottom of the shutter and latch to the sill of the window. These can only be used when you can open your window and access the rear of your shutters. The set comes with one latch an one catch, you will need two sets for each pair of shutters. Both pieces are made of cast iron. We recommend you prime and paint these before installation and screw them in with a screwdriver by hand, not with a drill. These do not come with screws.

     cincinatti catch

  • Small Victorian Foundation Vent

    Small Victorian Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 13″ wide and 8″ tall. The front measurement is 17-3/4″ wide and 12-1/4″ tall. The vent recesses into the foundation 3-1/2″ deep.

    Small Victorian Foundation

  • 8 Inch Shutter Slide Bolt

    8 Inch Shutter Slide Bolt. These slide shutter bolts are meant to mount to a pair of shutters in the space between the shutter and the window and function to fasten the shutters during a storm. The back plate, keeper, and straps are made of steel and the bolt itself is made of cast iron. They are powder coated in a glossy black finish.
    • They do not come with screws.
    • The back plate at the rear of the bolt measures 6-1/16″ x 1-11/16″
    • The bolt measures 7-51/16″ x 7/8″
    • The handle of the bolt projects 1-1/16″ from the rear
    • The keeper measures 2-1/4″ x 1-3/4″
    • The bolt throws 2-5/8″ out from the rear plate

    Ricca’s Architectural Sales

    511 North Solomon Street, New Orleans, LA 70119 (504) 488 – 5524 or (504) 822-8200 Fax: (504) 488 – 5662, Email: riccaarch@yahoo.com
    Business Hours:
    Tuesday – Friday 9 am – 5 pm Saturday – 9 am – 4 pm

    8 inch shutter slide bolt

  • Iron Parliament Hinge with Three Inch Offset

    Iron Parliament Hinge with Three Inch Offset measures a total of 5-1/8" wide and 2-7/8" tall. It mortises into the door or jamb 1" x 2-7/8" and has a throw of 3" when open. The pin on the hinge is removable making it function as either a right or left hand swing.

    five and an eigth parlament hinge

  • # 2  1/2 Right lull and Porter style Shutter Hinge

    # 2  1/2 Right Lull and Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.

    Hinge Width when open - 3-7/8"

    Hinge Throw from casing - 2-3/16"

    Hinge Height at mortise- 2-7/16"

    They do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a  drill.

    two and a half Right open rear

  • #  2 1/2 Left Lull and Porter style Shutter Hinge

    # 2 1/2 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.

    Hinge Width when open - 3-13/16"

    Hinge throw from casing - 2-1/16"

    Hinge Height at mortise - 2-9/16"

    They do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a  drill.

    two and a half left open rear

  • 6 Inch Shutter Slide Bolt

    6 Inch Shutter Slide Bolt. These slide bolts are meant to mount to a pair of shutters in the space between the shutter and the window and function to fasten the shutters during a storm. The back plate, keeper, and straps are made of steel and the bolt itself is made of cast iron. They are powder coated in a glossy black finish.

    They do not come with screws.

    The back plate at the rear of the bolt measures 5" x 1-3/4"

    The bolt measures 6-11/16" x 13/16"

    The handle of the bolt projects 1-1/16" from the rear

    The keeper measures 2-1/4" x 1-3/4"

    The bolt throws 1-15/16" out from the rear plate

    6 inch shutter slide bolt

  • Out of stock

    Brass Sash Pulley

    Brass Sash Pulley measures 4-3/4″ x 1-1/4″ at the face, it mortises 2-1/4″ deep into the jamb of the window.

    Brass Window Pulley

  • Brass Through Shutter Latch

    Brass Through Shutter Latch. These solid brass shutter latches are polished and lacquered to prevent immediate tarnish. They are intended to be mortised through the bottom of the shutter and hook to their keeper mounted on the window sill. When open they connect to a keeper mounted on the exterior of the home. These latches take the place of both dogs and slide bolts. These latches are meant for use on shutters 1-3/8" thick or less.  Each kit includes the latch, a plate for the rear of the shutter, a keeper for the sill, and a keeper for the wall. One kit will do a single shutter, you will need two kits for each window.

    The latch itself (the part that goes through the shutter) measures 2-3/8" at the top and 1-15/16" at the bottom

    The pull (the piece that you would operate) measures-1-1/4" tall and projects out 2" at the most (latch is 1-3/8" from the plate)

    The plate connected to the latch is 2" wide and 1-1/2" tall

    The plate that goes on the rear measures 1-3/8" tall and 1-1/2" wide

    The sill keeper (looks like bottle opener) is 1-3/4" deep and 1" wide

    The wall keeper (L shaped) is 1-1/16" tall, 15/16" wide and projects 1" from the wall

    Brass Through Shutter Latch Kit

  • # 0 Right Lull and Porter style Shutter Hinge

    # 0 Right Lull and Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.

    Hinge Width when open - 6-7/16"

    Hinge throw from casing - 4-1/8"

    Hinge Height at mortise-3-1/2"

    These do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a  drill.

     

    0 right open rear

  • Small Rectangular Foundation Vent

    Small Rectangular Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 13″ wide and 7-7/8″ tall. The front measurement is 15-1/8″ wide and 10-1/8″ tall. The vent recesses into the foundation 3″ deep.

    small rectangular foundation

  • Out of stock

    Brass Knuckle Sash Lock

    Brass Knuckle Sash Lock is meant for use with double hung windows. The lock comes with two pieces, the latching part, and the receiver which gets overlapped. These were found on most double hung sashes in New Orleans that predated the 1910's. The base of the latching part measures 1-7/8" x 13/16". The base of the receiver measures 1-7/8" x  3/4". It is made of solid brass.

    Brass Knuckle Sash Lock

  • # 1 1/2 Left Lull and Porter style Shutter Hinge

    # 1 1/2 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.

    Hinge Width when open - 5-1/8"

    Hinge throw from casing - 3-1/4"

    Hinge Height at mortise- 3"

    They do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.

    one and a half left open rear

  • Iron Pivot Hinge for Transoms

    Iron pivot hinge for transoms include one hinge- the pin side and the receiver side. You will need to order two in order to do one sash. These are made of cast iron and left unfinished.

    The pin side has the following measurements:

    Center to center of screw hole 1-1/2"

    Face of Hinge -2-3/8" tall, 7/8" wide, and mortises 1/8" into the face of the transom.

    Side of hinge- 5/8" tall, 7/8" wide, 1/8" thick, center of pin to edge 3/4", pin diameter 3/8", pin length 11/16"

    The receiver side has the following measurements:

    Center to center of screw hole 1-1/8"

    Diameter of center hole 7/16"

    1-11/16" tall, 3/4" wide and 1/8" deep

    Iron Pivot Hinges

  • Medium Victorian Foundation Vent

    Medium Victorian Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 17-7/8″ wide and 9-3/8″ tall. The front measurement is 22-7/8″ wide and 14-3/8″ tall. The vent recesses into the foundation 3-1/2″ deep.

    medium victorian foundation

  • # 1 1/2 Right Lull and Porter style Shutter Hinge

    # 1 1/2 Right Lull and Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.

    Hinge Width when open - 5"

    Hinge throw from casing - 3-1/4"

    Hinge Height at mortise - 2-7/8"

    They do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.

    one and a half right open rear

  • # 0 Left Lull and Porter style Shutter Hinge

    # 0 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.

    Hinge Width when open - 6-7/16"

    Hinge throw from casing - 4-1/8"

    Hinge Height at mortise- 3-1/2"

    These do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a  drill.

    0 left open rear

  • Large Rectangular Foundation Vent

    Large Rectangular Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 14-1/4" wide and 8-5/8" tall. The front measurement is 17-1/2" wide and 11-3/4" tall. The vent recesses into the foundation 3" deep.

    large rectangular foundation vent

  • Out of stock

    Brass Oval Beaded Sash Lift

    Brass Oval Beaded Sash Lift measures 4" x 2" and mortises into the sash 3/8" deep at 2-3/4" x 1-1/4".

    Oval Beaded Sash Lift

  • Large Victorian Foundation Vent

    Large Victorian Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 19″ wide and 10-5/8″ tall. The front measurement is 24-5/8″ wide and 16-1/4″ tall. The vent recesses into the foundation 3″ deep.

    large victorian foundation vent

  • # 1 Left Lull and Porter style Shutter Hinges

    # 1 Left Lull and Porter style Shutter Hinges. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.

    Hinge Width when open - 5-1/2"

    Hinge throw from casing - 3-11/16"

    Hinge Height at mortise-3-3/16"

    These do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a  drill.

     1 left open rear

  • Out of stock

    Brass Transom Latch

    Brass Transom Latch can be used in conjunction with pivoting transom hinges and would mount on the bottom rail of the transom, with the strike plate being mortised to the bottom of the transom's jamb. The latch is operated by pulling up on the loop at the top. (one of our clients suggests mounting a hook to the top of a broom stick to avoid getting on a stool.) The latch measures 2-1/8" wide, 1-1/4" tall, and 5/8" deep (with the loop standing 1-3/8" deep). The strike plate measures 1-3/4" wide, 1-1/2" deep, and mortises 1-3/4" x 3/4"x 3/16" into the jamb. It is made out of solid brass.

    Brass Transom Latch

  • # 2 Right Lull and Porter style Shutter Hinge

    # 2 Right Lull and Porter style Shutter Hinge. Right shutter hinge mounts on the left side of the window when looking at the window from outside of your home.

    Hinge Width when open - 4-7/16"

    Hinge throw from casing - 2-1/2"

    Hinge Height at mortise-2-7/8"

    They do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.

     2 right open rear

  • 12 Inch Shutter Slide Bolt

    12 Inch Shutter Slide Bolt. These slide bolts are meant to mount to a pair of shutters in the space between the shutter and the window and function to fasten the shutters during a storm. The back plate, keeper, and straps are made of steel and the bolt itself is made of cast iron. They are powder coated in a glossy black finish.

    They do not come with screws.

    The back plate at the rear of the bolt measures 8-13/16″ x 2-1/16″

    The bolt measures 8-3/16″ x 7/8″

    The handle of the bolt projects 3/4″ from the rear

    The keeper measures 3-13/16″ x 2-1/16″

    The bolt throws 3-3/4″ out from the rear plate

    12 Inch Shutter Slide Bolt12in Shutter Slide

  • # 2 Left Lull and Porter style Shutter Hinge

    # 2 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.

    Hinge Width when open - 4-7/16"

    Hinge throw from casing - 2-5/8"

    Hinge Height at mortise- 2-15/16"

    They do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.

    2 left open rear

  • 6 Inch Cast Iron Hook and Eye

    6 Inch Cast Iron Hook and Eye. Contains one hook and one eye. All components are made of cast iron and powder coated in a matte black finish.

    Hook length from center of hook to center of hole that attaches hook to the back plate- 5-3/8″

    Overall hook length- 6″

    Back plate size- 1-3/4″ x 1-3/8″  (1-1/4″ deep)

    Eye size- 1-3/4″ x 1-3/8″ (1-1/4″ deep)

    6 inch cast iron hook and eye

  • Clark Tip Left Shutter Hinge

    Clark Tip Left Shutter Hinge. For a face mount application when mortising a hinge is not an option. Left Hinges mount on the right side of the window when looking at the window from the exterior. These work well with use on brick homes or homes with wood casing. They are made from cast iron. We suggest you prime and paint these before installation, and screw them in by hand, not with a drill.

    These do not come with screws.

    Portion of hinge that mounts to the face of your casing- 1-1/2" x 2-1/2"

    Portion of hinge that mounts on the face of the shutter- 1-1/2" x 2-1/2"

    Throw provided by hinge when open- 3-1/4"

    Clarke tip left profile

  • Traditional Brass Sash Lock

    Traditional Brass Sash Lock is meant for use with double hung style windows.  The base of the latch measures 2-5/8" x 7/8" and the base of the keeper measures 2-1/2" x 5/8".

    Brass Traditional Sash Lock

  • Embossed Brass Pull

    Embossed Brass Pull measures 6-1/2" tall, 1-1/4" wide, and 1-1/4" deep.

    R-28

  • 4 Inch Cast Iron Hook and Eye with Diamond Shaped Backing

    4 Inch Cast Iron Hook and Eye with Diamond Shaped Backing. Contains one hook and one eye. All components are made of cast iron and powder coated in a matte black finish.

    Hook length from center of hook to center of hole that attaches hook to the back plate-4″

    Overall hook length- 4-1/2″

    Back plate size- 2″ x 1-3/8″  (7/8″ deep)

    Eye size- 2″ x 1-3/8″ (7/8″ deep)

    4 inch cast iron hook and eye diamond back

  • # 1 Right Lull and Porter style Shutter Hinge

    # 1 Right Lull and Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.

    Hinge Width when open - 5 -1/2"

    Hinge throw from casing - 3-5/8"

    Hinge Height at Mortise- 3-1/8"

    They do not come with screws.

    We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.

    1 right open rear

  • Brass Victorian Sash Lift

    Brass Victorian Sash Lift measures 5-1/4" x 1-3/4" and mortises 3/8" deep at 2-3/4" x 1-1/8".

    Victorian Sash Lift

  • 28 Inch Iron Head Bolt

    28 Inch Iron Head Bolt is most often used on a double door application and secures the stationary door at the top, it is highly recommended for use with a foot bolt (or bottom bolt) to prevent warping. The bolt measures 28-1/2" tall and the rear plate measures 1-15/16" wide by 6" tall. The bolt tongue measures 7/8" when activated, and is 3/4" wide. The bolt comes with two different keepers, one used when the door is flush with it's casing, and one used when the door is set deeper into its casing. It also comes with two stays used to keep the arm from being pulled from the surface of the door. It is important to note that in order to operate the bolt properly it must only be pulled up or down, never forward away from the surface of the door (this action would put stress on the weld that attaches the arm to the bolt).

    28 inch iron head bolt

  • 4 Inch Cast Iron Hook and Eye with Round Backing

    4 Inch Cast Iron Hook and Eye with Round Backing. Contains one hook and one eye. All components are made of cast iron and powder coated in a matte black finish.

    Hook length from center of hook to center of hole that attaches hook to the back plate- 3-1/2"

    Overall hook length- 4"

    Back plate size- 1-3/4" x 1-3/8"  (1-1/4" deep)

    Eye size- 1-3/4" x 1-3/8" (1-1/4" deep)

    4 inch cast iron hook and eye round back

  • Clark Tip Right Shutter Hinge

    Clark Tip Right Shutter Hinge. For a face mount application when mortising a hinge is not an option. Right hinges mount on the left side of the window when looking at the window from the exterior. These work well with use on brick homes or homes with wood casing. They are made from cast iron. We suggest you prime and paint these before installation, and screw them in by hand, not with a drill.

    These do not come with screws.

    Portion of hinge that mounts to the face of your casing- 1-1/2" x 2-1/2"

    Portion of hinge that mounts on the face of the shutter- 1-1/2" x 2-1/2"

    Throw provided by hinge when open- 3-1/4"

    clark tip right profile

  • Solid Brass Knob and Lever Set With Rosettes

    Solid Brass Knob and Lever Set with Rosettes. This set mimics screen door and small French door knob and lever sets found in New Orleans. The set comes with one knob, one lever, one circular rosette, one oval rosette, a shaft that connects the knob to the lever with set screws, and two set screws. This set will not work on predrilled doors, nor can it be made into "dummy knobs". It does not come with any latching or locking device.

    The knob measures 1-3/4" in diameter and rises 2-1/8" from the surface of the door

    The lever measures 3" long 7/8" in diameter at shank and rises 2-1/2" from the surface of the door

    The round rosette measures 1-3/4" in diameter

    The oval rosette measures 1-3/4" x 1-3/8"

    PA14

  • Iron Parliament Hinge with Four and Three Quarter Inch Offset

    Iron Parliament Hinge with Four and Three Quarter Inch Offset measures a total of 7″ wide and 3-3/8″ tall. It mortises into the door or jamb 1-1/8″ x 3-3/8″ and has a throw of 4-3/4″ when open. The pin on the hinge is removable making it function as either a right or left hand swing.

    seven inch parlament hinge

  • Iron Parliament Hinge with Four and a Quarter Inch Offset

    Iron Parliament Hinge with Four and a Quarter Inch Offset measures a total of 6-3/8″ wide and 2-7/8″ tall. It mortises into the door or jamb 1″ x 2-7/8″ and has a throw of 4-1/4″ when open. The pin on the hinge is removable making it function as either a right or left hand swing.

    six and three eigths parlament hinge

  • Out of stock

    Iron Arched Bin Pull

    Iron Arched Bin Pull measures 4" wide, 1-5/8" tall, and 1/2" deep. They are powder-coated black.

    R Bin Pull

Title

Go to Top