Brass Oval Beaded Sash Lift
Brass Oval Beaded Sash Lift measures 4" x 2" and mortises into the sash 3/8" deep at 2-3/4" x 1-1/4".
-
Brass Victorian Sash Lift
Brass Victorian Sash Lift measures 5-1/4" x 1-3/4" and mortises 3/8" deep at 2-3/4" x 1-1/8".
-
Iron Window Y
Iron Window Y's are used when the sash no longer stays up on it's own due to damaged or missing sash weights and balances. They mount to the jamb at about the level you want your window open and with a loose screw will pivot in or out of the way of the sash. The bottom of the sash is held up by the v shaped section, with the short end facing the exterior of the home.
The Y measures 2-5/8" long, 2" at it's widest point, and 1/4" thick. It is made of cast iron and painted white.
-
Iron Sash Pulley
Iron Sash Pulley measures 4-3/4" x 1-1/4" at the face, it mortises 2-3/8" deep into the jamb of the window.
-
Out of stock
Brass Sash Pulley
Brass Sash Pulley measures 4-3/4″ x 1-1/4″ at the face, it mortises 2-1/4″ deep into the jamb of the window.
-
Brass Embossed Sash Lock
Brass Embossed Sash Lock can be used either with casement or double hung windows. With double hung sashes the moving part of the latch would mount to the bottom sash and the keeper would mount to the top sash. The back plate of the keeper measures 2-3/8" x 7/8" and is a total of 3/4" tall. The back plate of the moving part of the latch measures 2-3/8" x 1-1/8". The arm measures 3-1/4" x 1".
-
Iron Pivot Hinge for Transoms
Iron pivot hinge for transoms include one hinge- the pin side and the receiver side. You will need to order two in order to do one sash. These are made of cast iron and left unfinished.
The pin side has the following measurements:
Center to center of screw hole 1-1/2"
Face of Hinge -2-3/8" tall, 7/8" wide, and mortises 1/8" into the face of the transom.
Side of hinge- 5/8" tall, 7/8" wide, 1/8" thick, center of pin to edge 3/4", pin diameter 3/8", pin length 11/16"
The receiver side has the following measurements:
Center to center of screw hole 1-1/8"
Diameter of center hole 7/16"
1-11/16" tall, 3/4" wide and 1/8" deep
-
Out of stock
Brass Pivot Hinge for Transoms
Brass pivot hinge for transoms include one hinge- the pin side and the receiver side. You will need to order two in order to do one sash. These are solid Brass with a lacquered finish.
The pin side has the following measurements:
Center to center of screw hole 1-1/8″
Face of Hinge -2-3/8″ tall, 1″ wide, and mortises 1/8″ into the face of the transom.
Side of hinge- 3/4″ tall, 1- 1/16″ wide, 3/16″ thick, center of pin to edge 7/8″, pin diameter 7/16″, pin length 15/16″
The receiver side has the following measurements:
Center to center of screw hole 1-1/4″
Diameter of center hole 3/8″
1-15/16″ tall, 7/8″ wide and 1/4″ deep
-
Out of stock
Iron Transom Latch
Iron Transom Latch can be used in conjunction with pivoting transom hinges and would mount on the bottom rail of the transom, with the strike plate being mortised to the bottom of the transom's jamb. The latch is operated by pulling up on the loop at the top. (one of our clients suggests mounting a hook to the top of a broom stick to avoid getting on a stool.) The latch measures 2-1/8" wide, 1-1/4" tall, and 5/8" deep (with the loop standing 1-3/8" deep). The strike plate measures 1-3/4" wide, 1-1/2" deep, and mortises 1-3/4" x 3/4"x 3/16" into the jamb. It is made out of cast iron and painted black.
-
Out of stock
Brass Transom Latch
Brass Transom Latch can be used in conjunction with pivoting transom hinges and would mount on the bottom rail of the transom, with the strike plate being mortised to the bottom of the transom's jamb. The latch is operated by pulling up on the loop at the top. (one of our clients suggests mounting a hook to the top of a broom stick to avoid getting on a stool.) The latch measures 2-1/8" wide, 1-1/4" tall, and 5/8" deep (with the loop standing 1-3/8" deep). The strike plate measures 1-3/4" wide, 1-1/2" deep, and mortises 1-3/4" x 3/4"x 3/16" into the jamb. It is made out of solid brass.
-
Large Plain Oval Foundation Vent
Large Plain Oval Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 14″ wide and 8-1/4″ tall. The front measurement is 18-1/4″ wide and 12-3/8″ tall. The vent recesses into the foundation 3-3/8″ deep.
-
Large Rectangular Foundation Vent
Large Rectangular Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 14-1/4" wide and 8-5/8" tall. The front measurement is 17-1/2" wide and 11-3/4" tall. The vent recesses into the foundation 3" deep.
-
Flat Victorian Foundation Vent
Flat Victorian Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally are screwed to the foundation. The measurement is 21-3/8″ wide and 13-5/8″ tall. The vent does not recess.
-
Small Plain Oval Foundation Vent
Small Plain Oval Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 12″ wide and 6-1/2″ tall. The front measurement is 15-7/8″ wide and 10-1/4″ tall. The vent recesses into the foundation 3″ deep.
-
Small Rectangular Foundation Vent
Small Rectangular Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 13″ wide and 7-7/8″ tall. The front measurement is 15-1/8″ wide and 10-1/8″ tall. The vent recesses into the foundation 3″ deep.
-
Large Victorian Foundation Vent
Large Victorian Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 19″ wide and 10-5/8″ tall. The front measurement is 24-5/8″ wide and 16-1/4″ tall. The vent recesses into the foundation 3″ deep.
-
Medium Victorian Foundation Vent
Medium Victorian Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 17-7/8″ wide and 9-3/8″ tall. The front measurement is 22-7/8″ wide and 14-3/8″ tall. The vent recesses into the foundation 3-1/2″ deep.
-
Small Victorian Foundation Vent
Small Victorian Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 13″ wide and 8″ tall. The front measurement is 17-3/4″ wide and 12-1/4″ tall. The vent recesses into the foundation 3-1/2″ deep.
-
Large Soffit Vent
Large Soffit Vent measures 17-1/16" in diameter. They are made of cast aluminum, and sold unfinished. These can be used for venting the attic from your soffit, or look great as a decorative piece on a wooden gate.
-
Out of stock
Medium Soffit Vent
Medium Soffit Vent measures 13-1/16" in diameter. They are made of cast aluminum, and sold unfinished. These can be used for venting the attic from your soffit, or look great as a decorative piece on a wooden gate, or even covers for can lighting on your front porch.
-
Out of stock
Small Soffit Vent
Small Soffit Vent measures 11-5/8" in diameter. They are made of cast aluminum, and sold unfinished. These can be used for venting the attic from your soffit, or look great as a decorative piece on a wooden gate.
-
Solid Brass Knob and Lever Set With Rosettes
Solid Brass Knob and Lever Set with Rosettes. This set mimics screen door and small French door knob and lever sets found in New Orleans. The set comes with one knob, one lever, one circular rosette, one oval rosette, a shaft that connects the knob to the lever with set screws, and two set screws. This set will not work on predrilled doors, nor can it be made into "dummy knobs". It does not come with any latching or locking device.
The knob measures 1-3/4" in diameter and rises 2-1/8" from the surface of the door
The lever measures 3" long 7/8" in diameter at shank and rises 2-1/2" from the surface of the door
The round rosette measures 1-3/4" in diameter
The oval rosette measures 1-3/4" x 1-3/8"
-
Out of stock
Solid Brass Gothic Knobs and Plates Set
Solid Brass Gothic Knobs and Plates Set. This set mimics what would be found in Arts and Crafts, Tudor, Gothic, and Spanish Revival homes . Cast out of solid brass and polished to a mirror finish, lacquered to prevent immediate tarnishing. It translates nicely when updating an older home while trying to maintain the small details that make an older home so appealing. The set comes with two back plates, two knobs, a shaft that connects the two knobs with set screws, and two set screws. These will not work with predrilled doors, but can not be made into “dummy knobs”. This set does not come with any locking or latching device.
The back plates measure 1-5/8″ x 6-1/8″ at their widest points
The knobs measure 2″ in diameter and rise 2-5/8″ from the surface of the door
-
Iron Beaded Oval Knobs and Plates Set
Iron Beaded Oval Knobs and Plates Set. This set mimics what would be found in some of the Creole homes in and around New Orleans. Cast out of iron and powder coated in a matte black finish. It translates nicely when modernizing and updating an older home while trying to maintain the small details that make an older home so appealing. The set comes with two back plates, two knobs, a shaft that connects the two knobs with set screws, and two set screws. These will not work with predrilled doors, but can be made into "dummy knobs" (call for price). This set does not come with any locking or latching device.
The back plates measure 2-3/8" x 7" at their widest points
The knobs measure 1-3/4" x 2-3/4" at their widest points and rise 2-3/4" from the surface of the door
