Brass Victorian Sash Lift
Brass Victorian Sash Lift measures 5-1/4" x 1-3/4" and mortises 3/8" deep at 2-3/4" x 1-1/8".
-
Iron Window Y
Iron Window Y's are used when the sash no longer stays up on it's own due to damaged or missing sash weights and balances. They mount to the jamb at about the level you want your window open and with a loose screw will pivot in or out of the way of the sash. The bottom of the sash is held up by the v shaped section, with the short end facing the exterior of the home.
The Y measures 2-5/8" long, 2" at it's widest point, and 1/4" thick. It is made of cast iron and painted white.
-
Iron Sash Pulley
Iron Sash Pulley measures 4-3/4" x 1-1/4" at the face, it mortises 2-3/8" deep into the jamb of the window.
-
Brass Sash Pulley
Brass Sash Pulley measures 4-3/4″ x 1-1/4″ at the face, it mortises 2-1/4″ deep into the jamb of the window.
-
Brass Embossed Sash Lock
Brass Embossed Sash Lock can be used either with casement or double hung windows. With double hung sashes the moving part of the latch would mount to the bottom sash and the keeper would mount to the top sash. The back plate of the keeper measures 2-3/8" x 7/8" and is a total of 3/4" tall. The back plate of the moving part of the latch measures 2-3/8" x 1-1/8". The arm measures 3-1/4" x 1".
-
Iron Pivot Hinge for Transoms
Iron pivot hinge for transoms include one hinge- the pin side and the receiver side. You will need to order two in order to do one sash. These are made of cast iron and left unfinished.
The pin side has the following measurements:
Center to center of screw hole 1-1/2"
Face of Hinge -2-3/8" tall, 7/8" wide, and mortises 1/8" into the face of the transom.
Side of hinge- 5/8" tall, 7/8" wide, 1/8" thick, center of pin to edge 3/4", pin diameter 3/8", pin length 11/16"
The receiver side has the following measurements:
Center to center of screw hole 1-1/8"
Diameter of center hole 7/16"
1-11/16" tall, 3/4" wide and 1/8" deep
-
Brass Pivot Hinge for Transoms
Brass pivot hinge for transoms include one hinge- the pin side and the receiver side. You will need to order two in order to do one sash. These are solid Brass with a lacquered finish.
The pin side has the following measurements:
Center to center of screw hole 1-1/8″
Face of Hinge -2-3/8″ tall, 1″ wide, and mortises 1/8″ into the face of the transom.
Side of hinge- 3/4″ tall, 1- 1/16″ wide, 3/16″ thick, center of pin to edge 7/8″, pin diameter 7/16″, pin length 15/16″
The receiver side has the following measurements:
Center to center of screw hole 1-1/4″
Diameter of center hole 3/8″
1-15/16″ tall, 7/8″ wide and 1/4″ deep
-
Iron Transom Latch
Iron Transom Latch can be used in conjunction with pivoting transom hinges and would mount on the bottom rail of the transom, with the strike plate being mortised to the bottom of the transom's jamb. The latch is operated by pulling up on the loop at the top. (one of our clients suggests mounting a hook to the top of a broom stick to avoid getting on a stool.) The latch measures 2-1/8" wide, 1-1/4" tall, and 5/8" deep (with the loop standing 1-3/8" deep). The strike plate measures 1-3/4" wide, 1-1/2" deep, and mortises 1-3/4" x 3/4"x 3/16" into the jamb. It is made out of cast iron and painted black.
-
Brass Transom Latch
Brass Transom Latch can be used in conjunction with pivoting transom hinges and would mount on the bottom rail of the transom, with the strike plate being mortised to the bottom of the transom's jamb. The latch is operated by pulling up on the loop at the top. (one of our clients suggests mounting a hook to the top of a broom stick to avoid getting on a stool.) The latch measures 2-1/8" wide, 1-1/4" tall, and 5/8" deep (with the loop standing 1-3/8" deep). The strike plate measures 1-3/4" wide, 1-1/2" deep, and mortises 1-3/4" x 3/4"x 3/16" into the jamb. It is made out of solid brass.
-
Large Plain Oval Foundation Vent
Large Plain Oval Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 14″ wide and 8-1/4″ tall. The front measurement is 18-1/4″ wide and 12-3/8″ tall. The vent recesses into the foundation 3-3/8″ deep.
-
Large Rectangular Foundation Vent
Large Rectangular Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 14-1/4" wide and 8-5/8" tall. The front measurement is 17-1/2" wide and 11-3/4" tall. The vent recesses into the foundation 3" deep.
-
Out of stock
Flat Victorian Foundation Vent
Flat Victorian Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally are screwed to the foundation. The measurement is 21-3/8″ wide and 13-5/8″ tall. The vent does not recess.
-
Small Plain Oval Foundation Vent
Small Plain Oval Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 12″ wide and 6-1/2″ tall. The front measurement is 15-7/8″ wide and 10-1/4″ tall. The vent recesses into the foundation 3″ deep.
-
Small Rectangular Foundation Vent
Small Rectangular Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 13″ wide and 7-7/8″ tall. The front measurement is 15-1/8″ wide and 10-1/8″ tall. The vent recesses into the foundation 3″ deep.
-
Large Victorian Foundation Vent
Large Victorian Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 19″ wide and 10-5/8″ tall. The front measurement is 24-5/8″ wide and 16-1/4″ tall. The vent recesses into the foundation 3″ deep.
-
Medium Victorian Foundation Vent
Medium Victorian Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 17-7/8″ wide and 9-3/8″ tall. The front measurement is 22-7/8″ wide and 14-3/8″ tall. The vent recesses into the foundation 3-1/2″ deep.
-
Small Victorian Foundation Vent
Small Victorian Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 13″ wide and 8″ tall. The front measurement is 17-3/4″ wide and 12-1/4″ tall. The vent recesses into the foundation 3-1/2″ deep.
-
Out of stock
Large Soffit Vent
Large Soffit Vent measures 17-1/16" in diameter. They are made of cast aluminum, and sold unfinished. These can be used for venting the attic from your soffit, or look great as a decorative piece on a wooden gate.
-
Out of stock
Medium Soffit Vent
Medium Soffit Vent measures 13-1/16" in diameter. They are made of cast aluminum, and sold unfinished. These can be used for venting the attic from your soffit, or look great as a decorative piece on a wooden gate, or even covers for can lighting on your front porch.
-
Out of stock
Small Soffit Vent
Small Soffit Vent measures 11-5/8" in diameter. They are made of cast aluminum, and sold unfinished. These can be used for venting the attic from your soffit, or look great as a decorative piece on a wooden gate.
-
Solid Brass Knob and Lever Set With Rosettes
Solid Brass Knob and Lever Set with Rosettes. This set mimics screen door and small French door knob and lever sets found in New Orleans. The set comes with one knob, one lever, one circular rosette, one oval rosette, a shaft that connects the knob to the lever with set screws, and two set screws. This set will not work on predrilled doors, nor can it be made into "dummy knobs". It does not come with any latching or locking device.
The knob measures 1-3/4" in diameter and rises 2-1/8" from the surface of the door
The lever measures 3" long 7/8" in diameter at shank and rises 2-1/2" from the surface of the door
The round rosette measures 1-3/4" in diameter
The oval rosette measures 1-3/4" x 1-3/8"
-
Out of stock
Solid Brass Gothic Knobs and Plates Set
Solid Brass Gothic Knobs and Plates Set. This set mimics what would be found in Arts and Crafts, Tudor, Gothic, and Spanish Revival homes . Cast out of solid brass and polished to a mirror finish, lacquered to prevent immediate tarnishing. It translates nicely when updating an older home while trying to maintain the small details that make an older home so appealing. The set comes with two back plates, two knobs, a shaft that connects the two knobs with set screws, and two set screws. These will not work with predrilled doors, but can not be made into “dummy knobs”. This set does not come with any locking or latching device.
The back plates measure 1-5/8″ x 6-1/8″ at their widest points
The knobs measure 2″ in diameter and rise 2-5/8″ from the surface of the door
-
Iron Beaded Oval Knobs and Plates Set
Iron Beaded Oval Knobs and Plates Set. This set mimics what would be found in some of the Creole homes in and around New Orleans. Cast out of iron and powder coated in a matte black finish. It translates nicely when modernizing and updating an older home while trying to maintain the small details that make an older home so appealing. The set comes with two back plates, two knobs, a shaft that connects the two knobs with set screws, and two set screws. These will not work with predrilled doors, but can be made into "dummy knobs" (call for price). This set does not come with any locking or latching device.
The back plates measure 2-3/8" x 7" at their widest points
The knobs measure 1-3/4" x 2-3/4" at their widest points and rise 2-3/4" from the surface of the door
-
Out of stock
Solid Brass Beaded Oval Knobs and Plates Set
Solid Brass Beaded Oval Knobs and Plates Set. This set mimics what would be found in some of the Creole homes in and around New Orleans. Cast out of solid brass and polished to a mirror finish, lacquered to prevent immediate tarnishing. It translates nicely when modernizing and updating an older home while trying to maintain the small details that make an older home so appealing. The set comes with two back plates, two knobs, a shaft that connects the two knobs with set screws, and two set screws. These will not work with predrilled doors, but can be made into “dummy knobs” (call for price). This set does not come with any locking or latching device.
The back plates measure 2-1/4″ x 7″ at their widest points
The knobs measure 1-5/8″ x 2-1/2″ at their widest points and rise 2-1/2″ from the surface of the door
-
Iron Parliament Hinge with Three Inch Offset
Iron Parliament Hinge with Three Inch Offset measures a total of 5-1/8" wide and 2-7/8" tall. It mortises into the door or jamb 1" x 2-7/8" and has a throw of 3" when open. The pin on the hinge is removable making it function as either a right or left hand swing.
-
Out of stock
Iron Parliament Hinge with Four and a Quarter Inch Offset
Iron Parliament Hinge with Four and a Quarter Inch Offset measures a total of 6-3/8″ wide and 2-7/8″ tall. It mortises into the door or jamb 1″ x 2-7/8″ and has a throw of 4-1/4″ when open. The pin on the hinge is removable making it function as either a right or left hand swing.
-
Iron Parliament Hinge with Four and Three Quarter Inch Offset
Iron Parliament Hinge with Four and Three Quarter Inch Offset measures a total of 7″ wide and 3-3/8″ tall. It mortises into the door or jamb 1-1/8″ x 3-3/8″ and has a throw of 4-3/4″ when open. The pin on the hinge is removable making it function as either a right or left hand swing.
-
Iron Parliament Hinge with Five and Three Quarter Inch Offset
Iron Parliament Hinge with Five and Three Quarter Inch Offset measures a total of 7-7/8″ wide and 2-7/8″ tall. It mortises into the door or jamb 1-1/16″ x 2-7/8″ and has a throw of 5-3/4″ when open. The pin on the hinge is removable making it function as either a right or left hand swing.
-
Embossed Steeple Top Hinges 3-1/2" x 3-1/2"
Embossed Iron Steeple Top Hinges 3-1/2″ x 3-1/2″ are sold in pairs of two (one hinge shown in images). These are made of cast iron and painted semi-gloss black. The pin is removable for ease of hanging. There is embossing on the face of the hinge. The pattern of the embossing is in a floral Victorian style.
-
Embossed Iron Steeple Top Hinges 4" x 4"
Embossed Iron Steeple Top Hinges 4" x 4" are sold in pairs of two (one hinge shown in images). These are made of cast iron and painted semi-gloss black. The pin is removable for ease of hanging. There is embossing on the face of the hinge and the reveal on the side of the hinge. The pattern of the embossing is in a linear Eastlake Victorian style.
-
Embossed Ball Top Iron Hinges 4" x 4"
Embossed Ball Top Iron Hinges 4" x 4" are sold in pairs of two (one hinge shown in images). These are made of cast iron and painted semi-gloss black. The pin is removable for ease of hanging. There is embossing on the face of the hinge and the reveal on the side of the hinge. The pattern of the embossing is in a linear Eastlake Victorian style.
-
Out of stock
Embossed Ball Top Hinges 4-1/4" x 4-7/8"
Embossed Ball Top Hinges 4-1/4" x 4-7/8" are sold in pairs of two (one hinge shown in images). These are made of cast iron and painted semi-gloss black. The pin is removable for ease of hanging. There is embossing on the face of the hinge, the spine of the hinge, and on both finials. The pattern of the embossing is in a floral Victorian style.
-
Ball Top Plain Iron Hinges 3-1/2" x 3-1/2"
Ball Top Plain Iron Hinges 3-1/2" x 3-1/2"- sold as a pair of two hinges (one hinge shown in images). These hinges are made of steel and painted gloss black. The pin is removable for ease of hanging.
-
Brass Ball Top Hinges 4-1/2" x 5"
Brass Ball Top Hinges 4-1/2" x 5" includes two hinges with removable pins.
-
Brass Ball Top Hinges 6" x 6"
Brass Ball Top Hinges 6" x 6" include two hinges with removable pins.
-
Three Inch Steeple Top Embossed Brass Hinges
Three Inch Steeple Top Embossed Brass Hinges are sold in pairs of two. They feature a removable pin for ease of installation.
-
Out of stock
Three and a Half Inch Steeple Top Embossed Brass Hinges
Three and a Half Inch Steeple Top Embossed Brass Hinges are sold in pairs of two. They feature a removable pin for ease of installation.
-
Four Inch Steeple Top Embossed Brass Hinges
Four Inch Steeple Top Embossed Brass Hinges are sold in pairs of two. They feature a removable pin for ease of installation.
-
Small Brass Door Bolt
Small Brass Door Bolts can be used for interior doors that require a locking function (ex. bathrooms or bedrooms) where the door is flush with the casing. This bolt measures 3-3/4" long and 1-3/8" wide, stands 1-1/4" tall from the surface of the door, and throws 10/16". The keeper measures 7/8" long and 1-1/4" tall.
-
Medium Brass Door Bolt
Medium Brass Door Bolts can be used for interior doors that require a locking function (ex. bathrooms or bedrooms) where the door is flush with the casing. This bolt measures 4-1/2″ long and 1-1/4″ wide, stands 1-1/2″ tall from the surface of the door, and throws 1-1/4″. The keeper measures 1-1/4″ long and 1-1/2″ tall.
-
Large Brass Door Bolt
Large Brass Door Bolts can be used for interior doors that require a locking function (ex. bathrooms or bedrooms) where the door is flush with the casing. This bolt measures 6-1/8″ long and 1-1/2″ wide, stands 1-1/2″ tall from the surface of the door, and throws 1-5/8″. The keeper measures 1-1/4″ long and 1-1/2″ tall.
-
Brass Flush Bolt
Brass Flush Bolt is used with double door sets on the stationary panel and mortises into the margin of the door at the top and bottom of the door. Two bolts would be needed to properly hold the door in place and prevent warping. These specific bolts are used when you do not want to see hardware when your doors are closed, achieving a cleaner, more modern look. the bolt measures 3/4" wide, 8" tall and 1-3/8" deep. Each bolt comes with a strike plate measuring 3/4"deep and 1-3/8" wide.
-
28 Inch Iron Head Bolt
28 Inch Iron Head Bolt is most often used on a double door application and secures the stationary door at the top, it is highly recommended for use with a foot bolt (or bottom bolt) to prevent warping. The bolt measures 28-1/2" tall and the rear plate measures 1-15/16" wide by 6" tall. The bolt tongue measures 7/8" when activated, and is 3/4" wide. The bolt comes with two different keepers, one used when the door is flush with it's casing, and one used when the door is set deeper into its casing. It also comes with two stays used to keep the arm from being pulled from the surface of the door. It is important to note that in order to operate the bolt properly it must only be pulled up or down, never forward away from the surface of the door (this action would put stress on the weld that attaches the arm to the bolt).
-
Out of stock
16 Inch Iron Head Bolt
16 Inch Iron Head Bolt is most often used on a double door application and secures the stationary door at the top, it is highly recommended for use with a foot bolt (or bottom bolt) to prevent warping. The bolt measures 16-3/4″ tall and the rear plate measures 1-7/8″ wide by 6″ tall. The bolt tongue measures 3/4″ when activated, and is 5/8″ wide. The bolt comes with two different keepers, one used when the door is flush with it’s casing, and one used when the door is set deeper into its casing. It also comes with one stay used to keep the arm from being pulled from the surface of the door. It is important to note that in order to operate the bolt properly it must only be pulled up or down, never forward away from the surface of the door (this action would put stress on the weld that attaches the arm to the bolt).
-
Out of stock
8 Inch Iron Foot Bolt
8 Inch Iron Foot Bolt is most often used on a double door application and secures the stationary door at the bottom, it is highly recommended for use with a head bolt (or top bolt) to prevent warping. The bolt measures 9-1/4″ tall and the rear plate measures 1-7/8″ wide by 5-1/2″ tall. The bolt tongue measures 1-1/16″ when activated, and is 3/4″ wide. The bolt comes with two different keepers, one used when the threshold extends well past the door and can be mortised into, and one used when the threshold does not extend much past the door. It is important to note that in order to operate the bolt properly it must only be pulled up or down with your hand, never forward away from the surface of the door, or operated with your foot (this action would put stress on the weld that attaches the arm to the bolt).
-
Brass Acanthus Door Bell
Brass Acanthus Door Bell measures 2-7/8" wide and 6-1/4" tall. This door bell is made for hard wired systems only- it will connect to your current door bell wiring with two screw terminals on the rear. It does not come with wiring or chimes. It attaches to your home with two wood screws.
-
Brass Eastlake Door Bell
Brass Eastlake Door Bell measures 2-1/4″ wide and 6-3/8″ tall. This door bell is made for hard wired systems only- it will connect to your current door bell wiring with two screw terminals on the rear. It does not come with wiring or chimes. It attaches to your home with two wood screws.
-
Iron Bat Door Knocker
Iron Bat door Knocker measures 2-3/4" wide, 9-1/8" tall and projects 1-5/8" from the surface of your door. It attaches to your door with two wood screws. This knocker is a replica of a knocker from one of Mr. Ricca's properties on the corner of Burgundy and Governor Nicholls streets.
-
Iron Lion Door Knocker
Iron Lion Door Knocker back plate measures 3-5/8" wide and 4-1/4" tall. The overall height is 5-7/8". The strike plate is 1-3/4" in diameter. The knocker and strike plate attach to your door with one machine style bolt each, that extends through the rear of your door.
-
Large Brass Bin Pull
Large Brass Bin Pull measures 4" wide, 1" tall, and 5/8" deep. the screw holes are 3-1/2" center to center.
-
Medium Brass Bin Pull
Medium Brass Bin Pull measures 3-1/2" wide, 1" tall, and 5/8" deep. The screw holes measure 3" center to center.
-
Small Brass Bin Pull
Small Brass Bin Pull measures 3-1/4" wide, 3/4" tall, and 5/8" deep. The screw holes measure 2-3/4" center to center.
-
Extra Large Brass Bin Pull
Extra Large Brass Bin Pull measure 3-3/8" wide, 1-1/4" tall, and 5/8" deep. The screw holes are 2-7/8" center to center.
-
Oval Iron Bin Pull
Oval Iron Bin Pull measures 3-3/8" wide, 1-3/8" tall, and 3/4" deep. The screw holes measure 2-7/8" center to center. They are painted black.
-
Iron Spanish Rose Bin Pull
Iron Spanish Rose Bin Pull measure 4-1/8" wide, 1-5/8" tall, and 1-1/16" deep. The screw holes measure 3-3/8" center to center. They are painted black.
-
Iron Ornate Fleur de Lis Bin Pull
Iron Ornate Fleur de Lis Bin Pull measures 4-1/4" wide, 1-1/2" tall, and 3/4" deep. The screw holes measure 2-3/4" center to center. They are painted black.
-
Iron Rectangular Bin Pull
Iron Rectangular Bin Pull measures 3-1/2" wide, 1-1/2" tall, and 3-4" deep. The screw holes measure 2-7/8" center to center. They are painted black.
-
Small Iron Fleur de Lis Pull
Small Iron Fleur de Lis Pull measure 4-1/8" long, 1-1/8" wide, and 7/8" deep. The screw holes measure 2-3/4" center to center. They are painted black.
-
Large Iron Fleur de Lis Pull
Large Iron Fleur de Lis Pull measures 7-1/4" tall, 1-1/2" wide, and 1-1/2" deep. The screw holes measure 5-5/16" center to center. They are painted black.
-
Large Iron Fleur de Lis Pull
Large Iron Fleur de Lis Pull measures 9" tall, 1-5/8" wide, and 1-7/8" deep. The screw holes measure 7-5/8" center to center. They are painted black.
