#3 Right Lull & Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.
Hinge Width when open - 3-1/4"
Hinge throw from casing - 1-3/8"
Hinge height at mortise -2-9/16"
These do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
# 0 Left Lull and Porter style Shutter Hinge
# 0 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.
Hinge Width when open - 6-7/16"
Hinge throw from casing - 4-1/8"
Hinge Height at mortise- 3-1/2"
These do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
# 0 Right Lull and Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.
Hinge Width when open - 6-7/16"
Hinge throw from casing - 4-1/8"
Hinge Height at mortise-3-1/2"
These do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
# 00 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.
Hinge Width when open – 8-7/8″
Hinge throw from casing – 6″
Hinge Height at mortise- 3-15/16″
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
# 00 Right Lull & Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.
Hinge Width when open – 8-3/4″
Hinge throw from casing – 6″
Hinge height at mortise -3-15/16″
These do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
# 1 1/2 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.
Hinge Width when open - 5-1/8"
Hinge throw from casing - 3-1/4"
Hinge Height at mortise- 3"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
# 1 1/2 Right Lull and Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.
Hinge Width when open - 5"
Hinge throw from casing - 3-1/4"
Hinge Height at mortise - 2-7/8"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
# 1 Left Lull and Porter style Shutter Hinges. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.
Hinge Width when open - 5-1/2"
Hinge throw from casing - 3-11/16"
Hinge Height at mortise-3-3/16"
These do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
# 1 Right Lull and Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.
Hinge Width when open - 5 -1/2"
Hinge throw from casing - 3-5/8"
Hinge Height at Mortise- 3-1/8"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
# 2 1/2 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.
Hinge Width when open - 3-13/16"
Hinge throw from casing - 2-1/16"
Hinge Height at mortise - 2-9/16"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
# 2 1/2 Right Lull and Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.
Hinge Width when open - 3-7/8"
Hinge Throw from casing - 2-3/16"
Hinge Height at mortise- 2-7/16"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
# 2 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.
Hinge Width when open - 4-7/16"
Hinge throw from casing - 2-5/8"
Hinge Height at mortise- 2-15/16"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
# 2 Right Lull and Porter style Shutter Hinge. Right shutter hinge mounts on the left side of the window when looking at the window from outside of your home.
Hinge Width when open - 4-7/16"
Hinge throw from casing - 2-1/2"
Hinge Height at mortise-2-7/8"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
# 3 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.
Hinge Width when open – 3-1/4″
Hinge throw from casing – 1-1/2″
Hinge Height at mortise- 2-9/16"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
10 Inch Shutter Slide Bolt. These slide bolts are meant to mount to a pair of shutters in the space between the shutter and the window and function to fasten the shutters during a storm. The back plate, keeper, and straps are made of steel and the bolt itself is made of cast iron. They are powder coated in a glossy black finish.
They do not come with screws.
The back plate at the rear of the bolt measures 6-3/4″ x 1-3/4″
The bolt measures 6" x 3/4″
The handle of the bolt projects 5/8″ from the rear
The keeper measures 2-5/8″ x 1-3/4″
The bolt throws 2-15/16″ out from the rear plate
12 Inch Shutter Slide Bolt. These slide bolts are meant to mount to a pair of shutters in the space between the shutter and the window and function to fasten the shutters during a storm. The back plate, keeper, and straps are made of steel and the bolt itself is made of cast iron. They are powder coated in a glossy black finish.
They do not come with screws.
The back plate at the rear of the bolt measures 8-13/16″ x 2-1/16″
The bolt measures 8-3/16″ x 7/8″
The handle of the bolt projects 3/4″ from the rear
The keeper measures 3-13/16″ x 2-1/16″
The bolt throws 3-3/4″ out from the rear plate
12 Inch Steel Hook and Eye. Contains one hook and one eye. All components are made of steel and left unfinished.
Hook length from center of hook to center of hole that attaches hook to the back plate- 11-1/4″
Overall hook length- 12″
Back plate size- 1-1/2″ x 3-3/8″ (1-1/4″ deep)
Eye size- 1-1/2″ x 3-3/8″ (3/4″ deep)
We recommend you prime and paint these before installation. They do not come with screws. It is ok to use a drill when installing this product.
12 Inch Steel Strap Hinge includes hinge and pintal. These heavy steel hinges have no offset, but can be bent to accommodate most offsets. We suggest priming and painting these before installation. You may use these on the left or right shutter. This product can be installed using a drill.
The exact measurements of the hinge itself are 12-1/2" long, 1-1/2" wide at widest point, tapers to 3/4" at the end.
The pintal measures 3-3/8" tall, 1-1/2" wide, and projects 1" from the back of the plate to the center of the pintal itself.
15 Inch Steel Hook and Eye. Contains one hook and one eye. All components are made of steel and left unfinished.
Hook length from center of hook to center of hole that attaches hook to the back plate- 14-1/2″
Overall hook length- 15-1/2″
Back plate size- 1-1/2″ x 3-3/8″ (1-1/4″ deep)
Eye size- 1-1/2″ x 3-3/8″ (3/4″ deep)
We recommend you prime and paint these before installation. They do not come with screws. It is ok to use a drill when installing this product.
15 Inch Steel Strap Hinge includes hinge and pintal. These heavy steel hinges have no offset, but can be bent to accommodate most offsets. We suggest priming and painting these before installation. You may use these on the left or right shutter. This product can be installed using a drill.
The exact measurements of the hinge itself are 15-1/4" long, 1-1/2" wide at widest point, tapers to 3/4" at the end.
The pintal measures 3-3/8" tall, 1-1/2" wide, and projects 1" from the back of the plate to the center of the pintal itself.
16 Inch Iron Head Bolt is most often used on a double door application and secures the stationary door at the top, it is highly recommended for use with a foot bolt (or bottom bolt) to prevent warping. The bolt measures 16-3/4″ tall and the rear plate measures 1-7/8″ wide by 6″ tall. The bolt tongue measures 3/4″ when activated, and is 5/8″ wide. The bolt comes with two different keepers, one used when the door is flush with it’s casing, and one used when the door is set deeper into its casing. It also comes with one stay used to keep the arm from being pulled from the surface of the door. It is important to note that in order to operate the bolt properly it must only be pulled up or down, never forward away from the surface of the door (this action would put stress on the weld that attaches the arm to the bolt).
17 Inch Steel Hook and Eye. Contains one hook and one eye. All components are made of steel and left unfinished.
Hook length from center of hook to center of hole that attaches hook to the back plate- 16″
Overall hook length- 17″
Back plate size- 1-1/2″ x 3-1/4″ (1-3/8″ deep)
Eye size- 1-1/2″ x 3-1/4″ (3/4″ deep)
17 Inch Steel Strap Hinge includes hinge and pintal. These heavy steel hinges have no offset, but can be bent to accommodate most offsets. We suggest priming and painting these before installation. You may use these on the left or right shutter. This product can be installed using a drill.
The exact measurements of the hinge itself are 17-1/4" long, 1-1/2" wide at widest point, tapers to 3/4" at the end.
The pintal measures 3-3/8" tall, 1-1/2" wide, and projects 1" from the back of the plate to the center of the pintal itself.
28 Inch Iron Head Bolt is most often used on a double door application and secures the stationary door at the top, it is highly recommended for use with a foot bolt (or bottom bolt) to prevent warping. The bolt measures 28-1/2" tall and the rear plate measures 1-15/16" wide by 6" tall. The bolt tongue measures 7/8" when activated, and is 3/4" wide. The bolt comes with two different keepers, one used when the door is flush with it's casing, and one used when the door is set deeper into its casing. It also comes with two stays used to keep the arm from being pulled from the surface of the door. It is important to note that in order to operate the bolt properly it must only be pulled up or down, never forward away from the surface of the door (this action would put stress on the weld that attaches the arm to the bolt).
4 Inch Cast Iron Hook and Eye with Diamond Shaped Backing. Contains one hook and one eye. All components are made of cast iron and powder coated in a matte black finish.
Hook length from center of hook to center of hole that attaches hook to the back plate-4″
Overall hook length- 4-1/2″
Back plate size- 2″ x 1-3/8″ (7/8″ deep)
Eye size- 2″ x 1-3/8″ (7/8″ deep)
4 Inch Cast Iron Hook and Eye with Round Backing. Contains one hook and one eye. All components are made of cast iron and powder coated in a matte black finish.
Hook length from center of hook to center of hole that attaches hook to the back plate- 3-1/2"
Overall hook length- 4"
Back plate size- 1-3/4" x 1-3/8" (1-1/4" deep)
Eye size- 1-3/4" x 1-3/8" (1-1/4" deep)
6 Inch Cast Iron Hook and Eye. Contains one hook and one eye. All components are made of cast iron and powder coated in a matte black finish.
Hook length from center of hook to center of hole that attaches hook to the back plate- 5-3/8″
Overall hook length- 6″
Back plate size- 1-3/4″ x 1-3/8″ (1-1/4″ deep)
Eye size- 1-3/4″ x 1-3/8″ (1-1/4″ deep)
6 Inch Shutter Pull. These pulls are usually located on the inner stile of a shutter in order to close it from inside of your window. The handle is done in a bail style and folds away to a 1/4" profile when not in use. These do not come with screws. The rear plate is steel and the handle is cast iron. They come powder coated in a matte black finish.
The Shutter Pulls have the following dimensions:
Height- 6-1/4"
Width- 1"
Center to Center of outer Screw Holes- 5-1/2"
Handle height- 3-7/8"
Handle Depth- 1-1/4"
6 Inch Shutter Slide Bolt. These slide bolts are meant to mount to a pair of shutters in the space between the shutter and the window and function to fasten the shutters during a storm. The back plate, keeper, and straps are made of steel and the bolt itself is made of cast iron. They are powder coated in a glossy black finish.
They do not come with screws.
The back plate at the rear of the bolt measures 5" x 1-3/4"
The bolt measures 6-11/16" x 13/16"
The handle of the bolt projects 1-1/16" from the rear
The keeper measures 2-1/4" x 1-3/4"
The bolt throws 1-15/16" out from the rear plate
8 Inch Cast Iron Hook and Eye. Contains one hook and one eye. All components are made of cast iron and powder coated in a matte black finish.
Hook length from center of hook to center of hole that attaches hook to the back plate- 7-7/16″
Overall hook length- 8″
Back plate size- 1-3/4″ x 1-3/8″ (1-1/4″ deep)
Eye size- 1-3/4″ x 1-3/8″ (1-1/4″ deep)
8 Inch Iron Foot Bolt is most often used on a double door application and secures the stationary door at the bottom, it is highly recommended for use with a head bolt (or top bolt) to prevent warping. The bolt measures 9-1/4″ tall and the rear plate measures 1-7/8″ wide by 5-1/2″ tall. The bolt tongue measures 1-1/16″ when activated, and is 3/4″ wide. The bolt comes with two different keepers, one used when the threshold extends well past the door and can be mortised into, and one used when the threshold does not extend much past the door. It is important to note that in order to operate the bolt properly it must only be pulled up or down with your hand, never forward away from the surface of the door, or operated with your foot (this action would put stress on the weld that attaches the arm to the bolt).
8 Inch Steel Hook and Eye. Contains one hook and one eye. All components are made of steel and left unfinished.
Hook length from center of hook to center of hole that attaches hook to the back plate- 7″
Overall hook length- 7-3/4″
Back plate size- 1-1/2″ x 3-3/8″ (1-1/4″ deep)
Eye size- 1-1/2″ x 3-3/8″ (3/4″ deep)
We recommend you prime and paint these before installation. They do not come with screws. It is ok to use a drill when installing this product.
8 Inch Steel Strap Hinge includes hinge and pintal. These heavy steel hinges have no offset, but can be bent to accommodate most offsets. We suggest priming and painting these before installation. You may use these on the left or right shutter. This product can be installed using a drill.
The exact measurements of the hinge itself are 8" long, 1-3/4" wide at widest point, tapers to 1/2" at the end.
The pintal measures 4-3/4" tall, 1-3/8" wide, and projects 1" from the back of the plate to the center of the pintal itself.
Ball Top Plain Iron Hinges 3-1/2" x 3-1/2"- sold as a pair of two hinges (one hinge shown in images). These hinges are made of steel and painted gloss black. The pin is removable for ease of hanging. 
Brass Acanthus Door Bell measures 2-7/8" wide and 6-1/4" tall. This door bell is made for hard wired systems only- it will connect to your current door bell wiring with two screw terminals on the rear. It does not come with wiring or chimes. It attaches to your home with two wood screws.
Brass Ball Top Hinges 4-1/2" x 5" includes two hinges with removable pins.
Brass Ball Top Hinges 6" x 6" include two hinges with removable pins.
Brass Casement Sash Latch comes with the latch, and three different keepers (one meant for use with a pair of casements which is surface mount and two meant for use with a single casement which mortises into the jamb).
The latch's back plate measures 2-1/16" tall, 1-5/16" wide and projects 2" from the surface of the window. The surface mount keeper measures 2" tall, 9/16" wide and projects 7/8" from the surface of the window. The first mortised keeper measures 2-1/8" tall, a total of 1-3/4" deep, and mortises 1" x 1/8" into the jamb and the second mortised keeper measures 5/8" x 2-3/8" x 1/16".
Brass Casement Stay is made to secure casement windows in either a closed or open position. The Maximum throw is 10-1/2". These are meant for use in an outswing application only.
Brass Eastlake Door Bell measures 2-1/4″ wide and 6-3/8″ tall. This door bell is made for hard wired systems only- it will connect to your current door bell wiring with two screw terminals on the rear. It does not come with wiring or chimes. It attaches to your home with two wood screws.
Brass Eastlake Pull measures 4-1/4" tall, 1-5/8" wide, and 1" deep.
Brass Embossed Sash Lock can be used either with casement or double hung windows. With double hung sashes the moving part of the latch would mount to the bottom sash and the keeper would mount to the top sash. The back plate of the keeper measures 2-3/8" x 7/8" and is a total of 3/4" tall. The back plate of the moving part of the latch measures 2-3/8" x 1-1/8". The arm measures 3-1/4" x 1".
Brass Fleur de Lis Pull measures 6-1/2" tall, 1-3/8" wide, and 1" deep. The screw holes measure 4-1/2" center to center.
Brass Flush Bolt is used with double door sets on the stationary panel and mortises into the margin of the door at the top and bottom of the door. Two bolts would be needed to properly hold the door in place and prevent warping. These specific bolts are used when you do not want to see hardware when your doors are closed, achieving a cleaner, more modern look. the bolt measures 3/4" wide, 8" tall and 1-3/8" deep. Each bolt comes with a strike plate measuring 3/4"deep and 1-3/8" wide.
Brass Knuckle Sash Lock is meant for use with double hung windows. The lock comes with two pieces, the latching part, and the receiver which gets overlapped. These were found on most double hung sashes in New Orleans that predated the 1910's. The base of the latching part measures 1-7/8" x 13/16". The base of the receiver measures 1-7/8" x 3/4". It is made of solid brass.
Brass Lion Door Knocker's back plate measures 3-1/4" wide and 4-1/4" tall, the overall height is 6". The strike plate measures 1-3/8" in diameter. The knocker and strike plate attach to your door with machine style bolts, that extend through the rear of your door.
Brass Oval Beaded Sash Lift measures 4" x 2" and mortises into the sash 3/8" deep at 2-3/4" x 1-1/4".
Brass pivot hinge for transoms include one hinge- the pin side and the receiver side. You will need to order two in order to do one sash. These are solid Brass with a lacquered finish.
The pin side has the following measurements:
Center to center of screw hole 1-1/8″
Face of Hinge -2-3/8″ tall, 1″ wide, and mortises 1/8″ into the face of the transom.
Side of hinge- 3/4″ tall, 1- 1/16″ wide, 3/16″ thick, center of pin to edge 7/8″, pin diameter 7/16″, pin length 15/16″
The receiver side has the following measurements:
Center to center of screw hole 1-1/4″
Diameter of center hole 3/8″
1-15/16″ tall, 7/8″ wide and 1/4″ deep
Brass Sash Pulley measures 4-3/4″ x 1-1/4″ at the face, it mortises 2-1/4″ deep into the jamb of the window.
Brass Through Shutter Latch. These solid brass shutter latches are polished and lacquered to prevent immediate tarnish. They are intended to be mortised through the bottom of the shutter and hook to their keeper mounted on the window sill. When open they connect to a keeper mounted on the exterior of the home. These latches take the place of both dogs and slide bolts. These latches are meant for use on shutters 1-3/8" thick or less. Each kit includes the latch, a plate for the rear of the shutter, a keeper for the sill, and a keeper for the wall. One kit will do a single shutter, you will need two kits for each window.
The latch itself (the part that goes through the shutter) measures 2-3/8" at the top and 1-15/16" at the bottom
The pull (the piece that you would operate) measures-1-1/4" tall and projects out 2" at the most (latch is 1-3/8" from the plate)
The plate connected to the latch is 2" wide and 1-1/2" tall
The plate that goes on the rear measures 1-3/8" tall and 1-1/2" wide
The sill keeper (looks like bottle opener) is 1-3/4" deep and 1" wide
The wall keeper (L shaped) is 1-1/16" tall, 15/16" wide and projects 1" from the wall
Brass Transom Latch can be used in conjunction with pivoting transom hinges and would mount on the bottom rail of the transom, with the strike plate being mortised to the bottom of the transom's jamb. The latch is operated by pulling up on the loop at the top. (one of our clients suggests mounting a hook to the top of a broom stick to avoid getting on a stool.) The latch measures 2-1/8" wide, 1-1/4" tall, and 5/8" deep (with the loop standing 1-3/8" deep). The strike plate measures 1-3/4" wide, 1-1/2" deep, and mortises 1-3/4" x 3/4"x 3/16" into the jamb. It is made out of solid brass.
Brass Victorian Sash Lift measures 5-1/4" x 1-3/4" and mortises 3/8" deep at 2-3/4" x 1-1/8".
Clark Tip Left Shutter Hinge. For a face mount application when mortising a hinge is not an option. Left Hinges mount on the right side of the window when looking at the window from the exterior. These work well with use on brick homes or homes with wood casing. They are made from cast iron. We suggest you prime and paint these before installation, and screw them in by hand, not with a drill.
These do not come with screws.
Portion of hinge that mounts to the face of your casing- 1-1/2" x 2-1/2"
Portion of hinge that mounts on the face of the shutter- 1-1/2" x 2-1/2"
Throw provided by hinge when open- 3-1/4"
Clark Tip Right Shutter Hinge. For a face mount application when mortising a hinge is not an option. Right hinges mount on the left side of the window when looking at the window from the exterior. These work well with use on brick homes or homes with wood casing. They are made from cast iron. We suggest you prime and paint these before installation, and screw them in by hand, not with a drill.
These do not come with screws.
Portion of hinge that mounts to the face of your casing- 1-1/2" x 2-1/2"
Portion of hinge that mounts on the face of the shutter- 1-1/2" x 2-1/2"
Throw provided by hinge when open- 3-1/4"
Embossed Ball Top Hinges 4-1/4" x 4-7/8" are sold in pairs of two (one hinge shown in images). These are made of cast iron and painted semi-gloss black. The pin is removable for ease of hanging. There is embossing on the face of the hinge, the spine of the hinge, and on both finials. The pattern of the embossing is in a floral Victorian style.
Embossed Ball Top Iron Hinges 4" x 4" are sold in pairs of two (one hinge shown in images). These are made of cast iron and painted semi-gloss black. The pin is removable for ease of hanging. There is embossing on the face of the hinge and the reveal on the side of the hinge. The pattern of the embossing is in a linear Eastlake Victorian style.
Embossed Brass Pull measures 6-1/2" tall, 1-1/4" wide, and 1-1/4" deep.
Embossed Iron Steeple Top Hinges 4" x 4" are sold in pairs of two (one hinge shown in images). These are made of cast iron and painted semi-gloss black. The pin is removable for ease of hanging. There is embossing on the face of the hinge and the reveal on the side of the hinge. The pattern of the embossing is in a linear Eastlake Victorian style.
Embossed kick bolts- available in two sizes and two finishes
The embossed kick bolts in the brass finish are made from solid, cast brass. The embossed kick bolts in the powder coated black are made from cast iron. These embossed kick bolts are designed to go at the bottom of the stationary door, shutter, or window when there are pairs of doors, shutters, or windows. We highly recommend you use these with a chain bolt (or top bolt) to prevent warping of your door.
The small bolts have the following measurements:
The bolt body measures 1-7/8 ” wide and 5-1/16″ tall, the tongue sticks out 1/2″ from the body of the latch when activated. The bolt is designed to be operated with your foot, the large button at the top activates it and the small button on the face deactivates it. The bolt comes with two strike plates- one measuring 1-7/8″wide and 2-3/8″ deep, and one measuring 2″ wide and 7/8″ deep.
The large bolts have the following measurements:
The bolt body measures 2 ” wide and 7-1/16″ tall, the tongue sticks out 3/4″ from the body of the latch when activated. The bolt is designed to be operated with your foot, the large button at the top activates it and the small button on the face deactivates it. The bolt comes with two strike plates- one measuring 1-7/8″wide and 2-3/8″ deep, and one measuring 2″ wide and 7/8″ deep.
Embossed Iron Steeple Top Hinges 3-1/2″ x 3-1/2″ are sold in pairs of two (one hinge shown in images). These are made of cast iron and painted semi-gloss black. The pin is removable for ease of hanging. There is embossing on the face of the hinge. The pattern of the embossing is in a floral Victorian style. 
Extra Large Brass Bin Pull measure 3-3/8" wide, 1-1/4" tall, and 5/8" deep. The screw holes are 2-7/8" center to center.
Four Inch Steeple Top Embossed Brass Hinges are sold in pairs of two. They feature a removable pin for ease of installation.
Iron Arched Bin Pull measures 4" wide, 1-5/8" tall, and 1/2" deep. They are powder-coated black.
Iron Bat door Knocker measures 2-3/4" wide, 9-1/8" tall and projects 1-5/8" from the surface of your door. It attaches to your door with two wood screws. This knocker is a replica of a knocker from one of Mr. Ricca's properties on the corner of Burgundy and Governor Nicholls streets.
Iron Beaded Oval Knobs and Plates Set. This set mimics what would be found in some of the Creole homes in and around New Orleans. Cast out of iron and powder coated in a matte black finish. It translates nicely when modernizing and updating an older home while trying to maintain the small details that make an older home so appealing. The set comes with two back plates, two knobs, a shaft that connects the two knobs with set screws, and two set screws. These will not work with predrilled doors, but can be made into "dummy knobs" (call for price). This set does not come with any locking or latching device.
The back plates measure 2-3/8" x 7" at their widest points
The knobs measure 1-3/4" x 2-3/4" at their widest points and rise 2-3/4" from the surface of the door
Iron Casement Sash Latch comes with the latch, and two different keepers (one meant for use with a pair of casements which is surface mount and one meant for use with a single casement which mortises into the jamb).
The latch's back plate measures 2-1/8" tall, 1-1/4" wide and projects 2" from the surface of the window. The surface mount keeper measures 2" tall, 9/16" wide and projects 7/8" from the surface of the window. The mortised keeper measures 2-1/8" tall, a total of 1-3/4" deep, and mortises 1" x 1/8" into the jamb.
Iron Casement Stay is made to secure casement windows in either a closed or open position. The Maximum throw is 10-1/2". These are meant for use in an outswing application only.
