-
# 3 Right Lull and Porter Style Shutter Hinge
#3 Right Lull & Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.
Hinge Width when open - 3-1/4"
Hinge throw from casing - 1-3/8"
Hinge height at mortise -2-9/16"
These do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
# 0 Left Lull and Porter style Shutter Hinge
# 0 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.
Hinge Width when open - 6-7/16"
Hinge throw from casing - 4-1/8"
Hinge Height at mortise- 3-1/2"
These do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
# 0 Right Lull and Porter style Shutter Hinge
# 0 Right Lull and Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.
Hinge Width when open - 6-7/16"
Hinge throw from casing - 4-1/8"
Hinge Height at mortise-3-1/2"
These do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
# 00 Left Lull and Porter style Shutter Hinge
# 00 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.
Hinge Width when open – 8-7/8″
Hinge throw from casing – 6″
Hinge Height at mortise- 3-15/16″
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
# 00 Right Lull and Porter Style Shutter Hinge
# 00 Right Lull & Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.
Hinge Width when open – 8-3/4″
Hinge throw from casing – 6″
Hinge height at mortise -3-15/16″
These do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
# 1 1/2 Left Lull and Porter style Shutter Hinge
# 1 1/2 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.
Hinge Width when open - 5-1/8"
Hinge throw from casing - 3-1/4"
Hinge Height at mortise- 3"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
# 1 1/2 Right Lull and Porter style Shutter Hinge
# 1 1/2 Right Lull and Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.
Hinge Width when open - 5"
Hinge throw from casing - 3-1/4"
Hinge Height at mortise - 2-7/8"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
# 1 Left Lull and Porter style Shutter Hinges
# 1 Left Lull and Porter style Shutter Hinges. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.
Hinge Width when open - 5-1/2"
Hinge throw from casing - 3-11/16"
Hinge Height at mortise-3-3/16"
These do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
# 1 Right Lull and Porter style Shutter Hinge
# 1 Right Lull and Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.
Hinge Width when open - 5 -1/2"
Hinge throw from casing - 3-5/8"
Hinge Height at Mortise- 3-1/8"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
# 2 1/2 Left Lull and Porter style Shutter Hinge
# 2 1/2 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.
Hinge Width when open - 3-13/16"
Hinge throw from casing - 2-1/16"
Hinge Height at mortise - 2-9/16"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
# 2 1/2 Right lull and Porter style Shutter Hinge
# 2 1/2 Right Lull and Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.
Hinge Width when open - 3-7/8"
Hinge Throw from casing - 2-3/16"
Hinge Height at mortise- 2-7/16"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
# 2 Left Lull and Porter style Shutter Hinge
# 2 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.
Hinge Width when open - 4-7/16"
Hinge throw from casing - 2-5/8"
Hinge Height at mortise- 2-15/16"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
# 2 Right Lull and Porter style Shutter Hinge
# 2 Right Lull and Porter style Shutter Hinge. Right shutter hinge mounts on the left side of the window when looking at the window from outside of your home.
Hinge Width when open - 4-7/16"
Hinge throw from casing - 2-1/2"
Hinge Height at mortise-2-7/8"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
# 3 Left Lull and Porter style Shutter Hinge
# 3 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.
Hinge Width when open – 3-1/4″
Hinge throw from casing – 1-1/2″
Hinge Height at mortise- 2-9/16"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
Out of stock
10 Arm Crystal Chandelier
This Czech Crystal (30% leaded) chandelier features 10 arms and is absolutely loaded with prisms. It dates back to the 1930's and was recently rebuilt and rewired. This one is a stunner! We cannot ship this product UPS , please call for a freight quote!
-
10 Inch Shutter Slide Bolt
10 Inch Shutter Slide Bolt. These slide bolts are meant to mount to a pair of shutters in the space between the shutter and the window and function to fasten the shutters during a storm. The back plate, keeper, and straps are made of steel and the bolt itself is made of cast iron. They are powder coated in a glossy black finish.
They do not come with screws.
The back plate at the rear of the bolt measures 6-3/4″ x 1-3/4″
The bolt measures 6" x 3/4″
The handle of the bolt projects 5/8″ from the rear
The keeper measures 2-5/8″ x 1-3/4″
The bolt throws 2-15/16″ out from the rear plate
-
12 Inch Shutter Slide Bolt
12 Inch Shutter Slide Bolt. These slide bolts are meant to mount to a pair of shutters in the space between the shutter and the window and function to fasten the shutters during a storm. The back plate, keeper, and straps are made of steel and the bolt itself is made of cast iron. They are powder coated in a glossy black finish.
They do not come with screws.
The back plate at the rear of the bolt measures 8-13/16″ x 2-1/16″
The bolt measures 8-3/16″ x 7/8″
The handle of the bolt projects 3/4″ from the rear
The keeper measures 3-13/16″ x 2-1/16″
The bolt throws 3-3/4″ out from the rear plate
-
Out of stock
15 Inch Steel Hook and Eye
12 Inch Steel Hook and Eye. Contains one hook and one eye. All components are made of steel and left unfinished.
Hook length from center of hook to center of hole that attaches hook to the back plate- 11-1/4″
Overall hook length- 12″
Back plate size- 1-1/2″ x 3-3/8″ (1-1/4″ deep)
Eye size- 1-1/2″ x 3-3/8″ (3/4″ deep)
We recommend you prime and paint these before installation. They do not come with screws. It is ok to use a drill when installing this product.
-
Out of stock
12 Inch Steel Strap Hinge
12 Inch Steel Strap Hinge includes hinge and pintal. These heavy steel hinges have no offset, but can be bent to accommodate most offsets. We suggest priming and painting these before installation. You may use these on the left or right shutter. This product can be installed using a drill.
The exact measurements of the hinge itself are 12-1/2" long, 1-1/2" wide at widest point, tapers to 3/4" at the end.
The pintal measures 3-3/8" tall, 1-1/2" wide, and projects 1" from the back of the plate to the center of the pintal itself.
-
Out of stock
15 Inch Steel Hook and Eye
15 Inch Steel Hook and Eye. Contains one hook and one eye. All components are made of steel and left unfinished.
Hook length from center of hook to center of hole that attaches hook to the back plate- 14-1/2″
Overall hook length- 15-1/2″
Back plate size- 1-1/2″ x 3-3/8″ (1-1/4″ deep)
Eye size- 1-1/2″ x 3-3/8″ (3/4″ deep)
We recommend you prime and paint these before installation. They do not come with screws. It is ok to use a drill when installing this product.
-
Out of stock
15 Inch Steel Strap Hinge
15 Inch Steel Strap Hinge includes hinge and pintal. These heavy steel hinges have no offset, but can be bent to accommodate most offsets. We suggest priming and painting these before installation. You may use these on the left or right shutter. This product can be installed using a drill.
The exact measurements of the hinge itself are 15-1/4" long, 1-1/2" wide at widest point, tapers to 3/4" at the end.
The pintal measures 3-3/8" tall, 1-1/2" wide, and projects 1" from the back of the plate to the center of the pintal itself.
-
Out of stock
16 Inch Iron Head Bolt
16 Inch Iron Head Bolt is most often used on a double door application and secures the stationary door at the top, it is highly recommended for use with a foot bolt (or bottom bolt) to prevent warping. The bolt measures 16-3/4″ tall and the rear plate measures 1-7/8″ wide by 6″ tall. The bolt tongue measures 3/4″ when activated, and is 5/8″ wide. The bolt comes with two different keepers, one used when the door is flush with it’s casing, and one used when the door is set deeper into its casing. It also comes with one stay used to keep the arm from being pulled from the surface of the door. It is important to note that in order to operate the bolt properly it must only be pulled up or down, never forward away from the surface of the door (this action would put stress on the weld that attaches the arm to the bolt).
-
Out of stock
17 Inch Steel Hook and Eye
17 Inch Steel Hook and Eye. Contains one hook and one eye. All components are made of steel and left unfinished.
Hook length from center of hook to center of hole that attaches hook to the back plate- 16″
Overall hook length- 17″
Back plate size- 1-1/2″ x 3-1/4″ (1-3/8″ deep)
Eye size- 1-1/2″ x 3-1/4″ (3/4″ deep)
-
Out of stock
17 Inch Steel Strap Hinge
17 Inch Steel Strap Hinge includes hinge and pintal. These heavy steel hinges have no offset, but can be bent to accommodate most offsets. We suggest priming and painting these before installation. You may use these on the left or right shutter. This product can be installed using a drill.
The exact measurements of the hinge itself are 17-1/4" long, 1-1/2" wide at widest point, tapers to 3/4" at the end.
The pintal measures 3-3/8" tall, 1-1/2" wide, and projects 1" from the back of the plate to the center of the pintal itself.
-
Out of stock
1920's Crystal 5 Arm Chandelier
This 1920's Crystal 5 Arm Chandelier has been cleaned and rewired and is ready to hang. It features Pendalogue crystals at the top and tear drop crystals hanging from the baubaches. There are five arms that take a standard base lamp (no greater than 40 watts each). The five shades are original to the fixture, one is cracked. You can choose to leave them on, or hang it without them.
The Measurements are as follows:
24" wide
24" tall body with crystal
13" of chain and canopy
The bottom of this chandelier would hang 37" from the ceiling, perfect for 8' ceilings.
This item is to large and delicate to ship using UPS, please call 504 488 5524 if you would like a commercial freight quote to get this item home!
-
28 Inch Iron Head Bolt
28 Inch Iron Head Bolt is most often used on a double door application and secures the stationary door at the top, it is highly recommended for use with a foot bolt (or bottom bolt) to prevent warping. The bolt measures 28-1/2" tall and the rear plate measures 1-15/16" wide by 6" tall. The bolt tongue measures 7/8" when activated, and is 3/4" wide. The bolt comes with two different keepers, one used when the door is flush with it's casing, and one used when the door is set deeper into its casing. It also comes with two stays used to keep the arm from being pulled from the surface of the door. It is important to note that in order to operate the bolt properly it must only be pulled up or down, never forward away from the surface of the door (this action would put stress on the weld that attaches the arm to the bolt).
-
Out of stock
3 Foot Gate
Our 3 foot gate is made from flat steel, hollow steel, and cast iron components. The gate comes with two hollow steel posts, with lift off style hinges included. With each gate you get to choose your finial style- either the spear finial (which matches our loop and spear fencing), or the Fleur de Lis finial. An image of each finial can be seen in the image gallery above. We do not always have these in stock, but we would be happy to order either style for you. If you are coordinating these with our loop and spear fencing, the 3 foot gate looks best with the 2 foot or the 3 foot tall fencing.
The measurements are as follows (measurements may vary slightly as this is a handmade product)
Gate width without hinges: 36"
Gate height at center- including finials: 36-1/4"
Gate height at sides: 30-1/4"
Post dimensions: 2" x 2"
MINIMUM Opening measurement required for installation: 41-1/2"
-
4 Inch Cast Iron Hook and Eye with Diamond Shaped Backing
4 Inch Cast Iron Hook and Eye with Diamond Shaped Backing. Contains one hook and one eye. All components are made of cast iron and powder coated in a matte black finish.
Hook length from center of hook to center of hole that attaches hook to the back plate-4″
Overall hook length- 4-1/2″
Back plate size- 2″ x 1-3/8″ (7/8″ deep)
Eye size- 2″ x 1-3/8″ (7/8″ deep)
-
4 Inch Cast Iron Hook and Eye with Round Backing
4 Inch Cast Iron Hook and Eye with Round Backing. Contains one hook and one eye. All components are made of cast iron and powder coated in a matte black finish.
Hook length from center of hook to center of hole that attaches hook to the back plate- 3-1/2"
Overall hook length- 4"
Back plate size- 1-3/4" x 1-3/8" (1-1/4" deep)
Eye size- 1-3/4" x 1-3/8" (1-1/4" deep)
-
Out of stock
4 Panel Interior Doors
4 panel interior doors come in three varieties:
Queen Anne Bead doors- Traditionally have raised panels with a beaded route done vertically through the center of each panel.
Raised Panel Doors- The most common of the four panel styles, has four raised panels.
Flat Panel With Applied Molding- The oldest of the four panel styles, features four flat panels with molding applied to both sides of the door framing the panels.
Four panel doors typically come in widths from 30" wide to 34" wide, although we do have some others in odd widths. The heights typically start around 79" and go to 90", although we do have some in odd heights. They range in thickness from 1" to 1-1/2".
Most of our doors are made of cypress. They are antique, used doors and will have holes, blemishes and other imperfections. We do offer refurbishment at an additional cost that depends on what needs to be done to the specific door.
-
Out of stock
5 Panel Interior Doors
5 Panel Interior Doors come in two main varieties:
Raised Panel- The panels are raised on both sides, and are mainly solid cypress doors.
Flat Panel- The panels are flat with either a shaker stile or a stepped profile stile. These doors can be cypress, but they are more common in fir with plywood panels.
Five panel doors typically come in widths from 26″ wide to 34″ wide, although we do have some others in odd widths. The heights typically start around 79″ and go to 84″, although we do have some in odd heights. They range in thickness from 1″ to 1-3/4″.
Most of our doors are made of cypress. They are antique, used doors and will have holes, blemishes and other imperfections. We do offer refurbishment at an additional cost that depends on what needs to be done to the specific door.
-
Out of stock
6 Arm Italian Brass and Crystal Chandelier
This 6 Arm Italian Brass and Crystal Chandelier is rewired and ready to hang. It features six brass arms, with genuine Beeswax candle covers, wired for chandelier base lamps (no greater than 40 watts each). It was probably manufactured between 1920 and 1935. It has crystal tear drops which refract the light perfectly. There is a crystal spear at the center of the fixture as well as a crystal ball at the bottom. This chandelier has brass acanthus leaves and scrolls.
The measurements are as follows:
30″ wide
33″ tall body with crystal
43″ of chain and canopy
The bottom of this chandelier would hang 76″ from the ceiling, perfect for 12′ or 14′ ceilings.
This item is to large and delicate to ship using UPS, please call 504 488 5524 if you would like a commercial freight quote to get this item home!
-
6 Inch Cast Iron Hook and Eye
6 Inch Cast Iron Hook and Eye. Contains one hook and one eye. All components are made of cast iron and powder coated in a matte black finish.
Hook length from center of hook to center of hole that attaches hook to the back plate- 5-3/8″
Overall hook length- 6″
Back plate size- 1-3/4″ x 1-3/8″ (1-1/4″ deep)
Eye size- 1-3/4″ x 1-3/8″ (1-1/4″ deep)
-
6 Inch Shutter Pull
6 Inch Shutter Pull. These pulls are usually located on the inner stile of a shutter in order to close it from inside of your window. The handle is done in a bail style and folds away to a 1/4" profile when not in use. These do not come with screws. The rear plate is steel and the handle is cast iron. They come powder coated in a matte black finish.
The Shutter Pulls have the following dimensions:
Height- 6-1/4"
Width- 1"
Center to Center of outer Screw Holes- 5-1/2"
Handle height- 3-7/8"
Handle Depth- 1-1/4"
-
6 Inch Shutter Slide Bolt
6 Inch Shutter Slide Bolt. These slide bolts are meant to mount to a pair of shutters in the space between the shutter and the window and function to fasten the shutters during a storm. The back plate, keeper, and straps are made of steel and the bolt itself is made of cast iron. They are powder coated in a glossy black finish.
They do not come with screws.
The back plate at the rear of the bolt measures 5" x 1-3/4"
The bolt measures 6-11/16" x 13/16"
The handle of the bolt projects 1-1/16" from the rear
The keeper measures 2-1/4" x 1-3/4"
The bolt throws 1-15/16" out from the rear plate
-
8 Inch Cast Iron Hook and Eye
8 Inch Cast Iron Hook and Eye. Contains one hook and one eye. All components are made of cast iron and powder coated in a matte black finish.
Hook length from center of hook to center of hole that attaches hook to the back plate- 7-7/16″
Overall hook length- 8″
Back plate size- 1-3/4″ x 1-3/8″ (1-1/4″ deep)
Eye size- 1-3/4″ x 1-3/8″ (1-1/4″ deep)
-
Out of stock
8 Inch Iron Foot Bolt
8 Inch Iron Foot Bolt is most often used on a double door application and secures the stationary door at the bottom, it is highly recommended for use with a head bolt (or top bolt) to prevent warping. The bolt measures 9-1/4″ tall and the rear plate measures 1-7/8″ wide by 5-1/2″ tall. The bolt tongue measures 1-1/16″ when activated, and is 3/4″ wide. The bolt comes with two different keepers, one used when the threshold extends well past the door and can be mortised into, and one used when the threshold does not extend much past the door. It is important to note that in order to operate the bolt properly it must only be pulled up or down with your hand, never forward away from the surface of the door, or operated with your foot (this action would put stress on the weld that attaches the arm to the bolt).
-
8 Inch Shutter Slide Bolt
8 Inch Shutter Slide Bolt. These slide shutter bolts are meant to mount to a pair of shutters in the space between the shutter and the window and function to fasten the shutters during a storm. The back plate, keeper, and straps are made of steel and the bolt itself is made of cast iron. They are powder coated in a glossy black finish.- They do not come with screws.
- The back plate at the rear of the bolt measures 6-1/16″ x 1-11/16″
- The bolt measures 7-51/16″ x 7/8″
- The handle of the bolt projects 1-1/16″ from the rear
- The keeper measures 2-1/4″ x 1-3/4″
- The bolt throws 2-5/8″ out from the rear plate
Ricca’s Architectural Sales
511 North Solomon Street, New Orleans, LA 70119 (504) 488 – 5524 or (504) 822-8200 Fax: (504) 488 – 5662, Email: riccaarch@yahoo.com
Business Hours:
Tuesday – Friday 9 am – 5 pm Saturday – 9 am – 4 pm -
Out of stock
8 Inch Steel Hook and Eye
8 Inch Steel Hook and Eye. Contains one hook and one eye. All components are made of steel and left unfinished.
Hook length from center of hook to center of hole that attaches hook to the back plate- 7″
Overall hook length- 7-3/4″
Back plate size- 1-1/2″ x 3-3/8″ (1-1/4″ deep)
Eye size- 1-1/2″ x 3-3/8″ (3/4″ deep)
We recommend you prime and paint these before installation. They do not come with screws. It is ok to use a drill when installing this product.
-
8 Inch Steel Strap Hinge
8 Inch Steel Strap Hinge includes hinge and pintal. These heavy steel hinges have no offset, but can be bent to accommodate most offsets. We suggest priming and painting these before installation. You may use these on the left or right shutter. This product can be installed using a drill.
The exact measurements of the hinge itself are 8" long, 1-3/4" wide at widest point, tapers to 1/2" at the end.
The pintal measures 4-3/4" tall, 1-3/8" wide, and projects 1" from the back of the plate to the center of the pintal itself.
-
Out of stock
9 Light Marginal Doors
9 Light marginal doors- Available in both 6'8" and 8'0" heights. These doors are made of Mahogany and feature beveled, tempered glass. These are sold as slabs only and do not come prehung. It is important to note that if you are ordering pairs of sidelights - each listing is for a single slab, so you will need to order two slabs to make a pair.
The following sizes are available:
36" x 80" x 1-3/4" (Currently out of stock)
32" x 80" x 1-3/4"
30" x 80" x 1-3/4"
18" x 80" x 1-3/4" (6 light sidelight- see photos)
14" x 80" x 1-3/4" (3 light sidelight- see photos)
36" x 96" x 1-3/4"
32" x 96" x 1-3/4"
18" x 96" x 1-3/4" (6 light sidelight)
-
Out of stock
Antique Stewart Iron Works Wrought Iron Gate
Antique Stewart Iron Works Wrought Iron Gate
This gate, manufactured in Cincinnati, Ohio by the Stewart Ironworks Company, measures 37" wide with the mounting hardware and primitive latch, or 31-1/2" wide as just the gate. It measures 52" tall at the center, and 42" tall at the sides. It needs a weld at the bottom right corner, the top finial is slightly bent, and may need some bondo work at the top left, but is otherwise in great shape for its age. There is a great makers plaque at the center, pictured in the gallery of images. The primitive latch is still functioning. The gate comes with the portion of the hinge that bolts to your fence post and the rod that attaches your gate to the hinge. The iron details on this gate are exquisite. Please call for a shipping quote if you are interested in this gate as we cannot ship it using UPS.
-
Out of stock
Ashley Hanging Lantern
The Ashley hanging lantern is hand made in the united states. Made of solid copper with brass fittings, these lanterns are handmade items and can take up to five weeks for delivery. Several options are available: Finish: Copper (standard), Bronze, or Black Function: Electric with one, or two lights
Please call 504 488 5524 to order as we do not stock these items. (the lantern shown is copper with the electric single light function)