Iron Parliament Hinge with Four and a Quarter Inch Offset measures a total of 6-3/8″ wide and 2-7/8″ tall. It mortises into the door or jamb 1″ x 2-7/8″ and has a throw of 4-1/4″ when open. The pin on the hinge is removable making it function as either a right or left hand swing.
Small Plain Oval Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 12″ wide and 6-1/2″ tall. The front measurement is 15-7/8″ wide and 10-1/4″ tall. The vent recesses into the foundation 3″ deep.
Brass Eastlake Pull measures 4-1/4" tall, 1-5/8" wide, and 1" deep.
Three and a Half Inch Steeple Top Embossed Brass Hinges are sold in pairs of two. They feature a removable pin for ease of installation.
Solid Brass Beaded Oval Knobs and Plates Set. This set mimics what would be found in some of the Creole homes in and around New Orleans. Cast out of solid brass and polished to a mirror finish, lacquered to prevent immediate tarnishing. It translates nicely when modernizing and updating an older home while trying to maintain the small details that make an older home so appealing. The set comes with two back plates, two knobs, a shaft that connects the two knobs with set screws, and two set screws. These will not work with predrilled doors, but can be made into “dummy knobs” (call for price). This set does not come with any locking or latching device.
The back plates measure 2-1/4″ x 7″ at their widest points
The knobs measure 1-5/8″ x 2-1/2″ at their widest points and rise 2-1/2″ from the surface of the door
Embossed Iron Steeple Top Hinges 4" x 4" are sold in pairs of two (one hinge shown in images). These are made of cast iron and painted semi-gloss black. The pin is removable for ease of hanging. There is embossing on the face of the hinge and the reveal on the side of the hinge. The pattern of the embossing is in a linear Eastlake Victorian style.
Solid Brass Broken Leaf Door Knobs and Plates Set. Originally patented in 1887 by Lockwood Manufacturing Company, the “Broken Leaf” pattern was widely used at the end of the Victorian era, a style that has come to be known as Eastlake. We have interpreted the original design into a lovely set of solid cast brass hardware. The set is composed of two back plates, two slip on knobs, a shaft that connects the two knobs by set screws, and two set screws. This set will not work for predrilled doors, nor can it be made into “dummy knobs”. They do not come with any latch or locking device.
The plates measure 1-1/2″ x 5-5/16″
The Knobs are 2-1/4″ in diameter
The set projects 2-1/2″ from the face of the door
8 Inch Cast Iron Hook and Eye. Contains one hook and one eye. All components are made of cast iron and powder coated in a matte black finish.
Hook length from center of hook to center of hole that attaches hook to the back plate- 7-7/16″
Overall hook length- 8″
Back plate size- 1-3/4″ x 1-3/8″ (1-1/4″ deep)
Eye size- 1-3/4″ x 1-3/8″ (1-1/4″ deep)
Solid Brass Ball Bearing Hinges - ball finial in 3-1/2" x 3-1/2"
These hinges are made from solid brass, polished to a high shine and lacquered to prevent immediate tarnishing. The ball bearing helps to prevent the solid brass hinge from wearing down when used on heavier doors. They are sold as pairs (two hinges per package) and come with screws.
Currently available in 3-1/2" x 3-1/2". Features five knuckles with two ball bearings and three screw holes per side.
12 Inch Steel Strap Hinge includes hinge and pintal. These heavy steel hinges have no offset, but can be bent to accommodate most offsets. We suggest priming and painting these before installation. You may use these on the left or right shutter. This product can be installed using a drill.
The exact measurements of the hinge itself are 12-1/2" long, 1-1/2" wide at widest point, tapers to 3/4" at the end.
The pintal measures 3-3/8" tall, 1-1/2" wide, and projects 1" from the back of the plate to the center of the pintal itself.
Large Brass Door Bolts can be used for interior doors that require a locking function (ex. bathrooms or bedrooms) where the door is flush with the casing. This bolt measures 6-1/8″ long and 1-1/2″ wide, stands 1-1/2″ tall from the surface of the door, and throws 1-5/8″. The keeper measures 1-1/4″ long and 1-1/2″ tall.
Brass Casement Sash Latch comes with the latch, and three different keepers (one meant for use with a pair of casements which is surface mount and two meant for use with a single casement which mortises into the jamb).
The latch's back plate measures 2-1/16" tall, 1-5/16" wide and projects 2" from the surface of the window. The surface mount keeper measures 2" tall, 9/16" wide and projects 7/8" from the surface of the window. The first mortised keeper measures 2-1/8" tall, a total of 1-3/4" deep, and mortises 1" x 1/8" into the jamb and the second mortised keeper measures 5/8" x 2-3/8" x 1/16".
8 Inch Iron Foot Bolt is most often used on a double door application and secures the stationary door at the bottom, it is highly recommended for use with a head bolt (or top bolt) to prevent warping. The bolt measures 9-1/4″ tall and the rear plate measures 1-7/8″ wide by 5-1/2″ tall. The bolt tongue measures 1-1/16″ when activated, and is 3/4″ wide. The bolt comes with two different keepers, one used when the threshold extends well past the door and can be mortised into, and one used when the threshold does not extend much past the door. It is important to note that in order to operate the bolt properly it must only be pulled up or down with your hand, never forward away from the surface of the door, or operated with your foot (this action would put stress on the weld that attaches the arm to the bolt).
Large Plain Oval Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 14″ wide and 8-1/4″ tall. The front measurement is 18-1/4″ wide and 12-3/8″ tall. The vent recesses into the foundation 3-3/8″ deep.
Embossed kick bolts- available in two sizes and two finishes
The embossed kick bolts in the brass finish are made from solid, cast brass. The embossed kick bolts in the powder coated black are made from cast iron. These embossed kick bolts are designed to go at the bottom of the stationary door, shutter, or window when there are pairs of doors, shutters, or windows. We highly recommend you use these with a chain bolt (or top bolt) to prevent warping of your door.
The small bolts have the following measurements:
The bolt body measures 1-7/8 ” wide and 5-1/16″ tall, the tongue sticks out 1/2″ from the body of the latch when activated. The bolt is designed to be operated with your foot, the large button at the top activates it and the small button on the face deactivates it. The bolt comes with two strike plates- one measuring 1-7/8″wide and 2-3/8″ deep, and one measuring 2″ wide and 7/8″ deep.
The large bolts have the following measurements:
The bolt body measures 2 ” wide and 7-1/16″ tall, the tongue sticks out 3/4″ from the body of the latch when activated. The bolt is designed to be operated with your foot, the large button at the top activates it and the small button on the face deactivates it. The bolt comes with two strike plates- one measuring 1-7/8″wide and 2-3/8″ deep, and one measuring 2″ wide and 7/8″ deep.
Iron Casement Sash Latch comes with the latch, and two different keepers (one meant for use with a pair of casements which is surface mount and one meant for use with a single casement which mortises into the jamb).
The latch's back plate measures 2-1/8" tall, 1-1/4" wide and projects 2" from the surface of the window. The surface mount keeper measures 2" tall, 9/16" wide and projects 7/8" from the surface of the window. The mortised keeper measures 2-1/8" tall, a total of 1-3/4" deep, and mortises 1" x 1/8" into the jamb.
17 Inch Steel Hook and Eye. Contains one hook and one eye. All components are made of steel and left unfinished.
Hook length from center of hook to center of hole that attaches hook to the back plate- 16″
Overall hook length- 17″
Back plate size- 1-1/2″ x 3-1/4″ (1-3/8″ deep)
Eye size- 1-1/2″ x 3-1/4″ (3/4″ deep)
Brass Casement Stay is made to secure casement windows in either a closed or open position. The Maximum throw is 10-1/2". These are meant for use in an outswing application only.
10 Inch Shutter Slide Bolt. These slide bolts are meant to mount to a pair of shutters in the space between the shutter and the window and function to fasten the shutters during a storm. The back plate, keeper, and straps are made of steel and the bolt itself is made of cast iron. They are powder coated in a glossy black finish.
They do not come with screws.
The back plate at the rear of the bolt measures 6-3/4″ x 1-3/4″
The bolt measures 6" x 3/4″
The handle of the bolt projects 5/8″ from the rear
The keeper measures 2-5/8″ x 1-3/4″
The bolt throws 2-15/16″ out from the rear plate
Iron Oval Pull measures 1-3/4" tall, 1-1/8" wide, and 1-1/2" deep. It mounts with an attached wood screw.
Three Inch Steeple Top Embossed Brass Hinges are sold in pairs of two. They feature a removable pin for ease of installation.
Large Iron Fleur de Lis Pull measures 9" tall, 1-5/8" wide, and 1-7/8" deep. The screw holes measure 7-5/8" center to center. They are painted black.
