-
Out of stock
Small Soffit Vent
Small Soffit Vent measures 11-5/8" in diameter. They are made of cast aluminum, and sold unfinished. These can be used for venting the attic from your soffit, or look great as a decorative piece on a wooden gate.
-
Brass Pivot Hinge for Transoms
Brass pivot hinge for transoms include one hinge- the pin side and the receiver side. You will need to order two in order to do one sash. These are solid Brass with a lacquered finish.
The pin side has the following measurements:
Center to center of screw hole 1-1/8″
Face of Hinge -2-3/8″ tall, 1″ wide, and mortises 1/8″ into the face of the transom.
Side of hinge- 3/4″ tall, 1- 1/16″ wide, 3/16″ thick, center of pin to edge 7/8″, pin diameter 7/16″, pin length 15/16″
The receiver side has the following measurements:
Center to center of screw hole 1-1/4″
Diameter of center hole 3/8″
1-15/16″ tall, 7/8″ wide and 1/4″ deep
-
6 Inch Shutter Pull
6 Inch Shutter Pull. These pulls are usually located on the inner stile of a shutter in order to close it from inside of your window. The handle is done in a bail style and folds away to a 1/4" profile when not in use. These do not come with screws. The rear plate is steel and the handle is cast iron. They come powder coated in a matte black finish.
The Shutter Pulls have the following dimensions:
Height- 6-1/4"
Width- 1"
Center to Center of outer Screw Holes- 5-1/2"
Handle height- 3-7/8"
Handle Depth- 1-1/4"
-
# 3 Right Lull and Porter Style Shutter Hinge
#3 Right Lull & Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.
Hinge Width when open - 3-1/4"
Hinge throw from casing - 1-3/8"
Hinge height at mortise -2-9/16"
These do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
Out of stock
Flat Victorian Foundation Vent
Flat Victorian Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally are screwed to the foundation. The measurement is 21-3/8″ wide and 13-5/8″ tall. The vent does not recess.
-
Out of stock
Large Soffit Vent
Large Soffit Vent measures 17-1/16" in diameter. They are made of cast aluminum, and sold unfinished. These can be used for venting the attic from your soffit, or look great as a decorative piece on a wooden gate.
-
# 3 Left Lull and Porter style Shutter Hinge
# 3 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.
Hinge Width when open – 3-1/4″
Hinge throw from casing – 1-1/2″
Hinge Height at mortise- 2-9/16"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
Out of stock
Medium Soffit Vent
Medium Soffit Vent measures 13-1/16" in diameter. They are made of cast aluminum, and sold unfinished. These can be used for venting the attic from your soffit, or look great as a decorative piece on a wooden gate, or even covers for can lighting on your front porch.
-
Brass Through Shutter Latch
Brass Through Shutter Latch. These solid brass shutter latches are polished and lacquered to prevent immediate tarnish. They are intended to be mortised through the bottom of the shutter and hook to their keeper mounted on the window sill. When open they connect to a keeper mounted on the exterior of the home. These latches take the place of both dogs and slide bolts. These latches are meant for use on shutters 1-3/8" thick or less. Each kit includes the latch, a plate for the rear of the shutter, a keeper for the sill, and a keeper for the wall. One kit will do a single shutter, you will need two kits for each window.
The latch itself (the part that goes through the shutter) measures 2-3/8" at the top and 1-15/16" at the bottom
The pull (the piece that you would operate) measures-1-1/4" tall and projects out 2" at the most (latch is 1-3/8" from the plate)
The plate connected to the latch is 2" wide and 1-1/2" tall
The plate that goes on the rear measures 1-3/8" tall and 1-1/2" wide
The sill keeper (looks like bottle opener) is 1-3/4" deep and 1" wide
The wall keeper (L shaped) is 1-1/16" tall, 15/16" wide and projects 1" from the wall
-
Shutter Catches
Shutter Catches. These typically mount at the bottom of the shutter and latch to the sill of the window. These can only be used when you can open your window and access the rear of your shutters. The set comes with one latch an one catch, you will need two sets for each pair of shutters. Both pieces are made of cast iron. We recommend you prime and paint these before installation and screw them in with a screwdriver by hand, not with a drill. These do not come with screws.
-
# 2 1/2 Right lull and Porter style Shutter Hinge
# 2 1/2 Right Lull and Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.
Hinge Width when open - 3-7/8"
Hinge Throw from casing - 2-3/16"
Hinge Height at mortise- 2-7/16"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
# 2 1/2 Left Lull and Porter style Shutter Hinge
# 2 1/2 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.
Hinge Width when open - 3-13/16"
Hinge throw from casing - 2-1/16"
Hinge Height at mortise - 2-9/16"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
12 Inch Shutter Slide Bolt
12 Inch Shutter Slide Bolt. These slide bolts are meant to mount to a pair of shutters in the space between the shutter and the window and function to fasten the shutters during a storm. The back plate, keeper, and straps are made of steel and the bolt itself is made of cast iron. They are powder coated in a glossy black finish.
They do not come with screws.
The back plate at the rear of the bolt measures 8-13/16″ x 2-1/16″
The bolt measures 8-3/16″ x 7/8″
The handle of the bolt projects 3/4″ from the rear
The keeper measures 3-13/16″ x 2-1/16″
The bolt throws 3-3/4″ out from the rear plate
-
Small Victorian Foundation Vent
Small Victorian Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 13″ wide and 8″ tall. The front measurement is 17-3/4″ wide and 12-1/4″ tall. The vent recesses into the foundation 3-1/2″ deep.
-
8 Inch Shutter Slide Bolt
8 Inch Shutter Slide Bolt. These slide shutter bolts are meant to mount to a pair of shutters in the space between the shutter and the window and function to fasten the shutters during a storm. The back plate, keeper, and straps are made of steel and the bolt itself is made of cast iron. They are powder coated in a glossy black finish.- They do not come with screws.
- The back plate at the rear of the bolt measures 6-1/16″ x 1-11/16″
- The bolt measures 7-51/16″ x 7/8″
- The handle of the bolt projects 1-1/16″ from the rear
- The keeper measures 2-1/4″ x 1-3/4″
- The bolt throws 2-5/8″ out from the rear plate
Ricca’s Architectural Sales
511 North Solomon Street, New Orleans, LA 70119 (504) 488 – 5524 or (504) 822-8200 Fax: (504) 488 – 5662, Email: riccaarch@yahoo.com
Business Hours:
Tuesday – Friday 9 am – 5 pm Saturday – 9 am – 4 pm
-
Small Rectangular Foundation Vent
Small Rectangular Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 13″ wide and 7-7/8″ tall. The front measurement is 15-1/8″ wide and 10-1/8″ tall. The vent recesses into the foundation 3″ deep.
-
Iron Parliament Hinge with Three Inch Offset
Iron Parliament Hinge with Three Inch Offset measures a total of 5-1/8" wide and 2-7/8" tall. It mortises into the door or jamb 1" x 2-7/8" and has a throw of 3" when open. The pin on the hinge is removable making it function as either a right or left hand swing.
-
6 Inch Shutter Slide Bolt
6 Inch Shutter Slide Bolt. These slide bolts are meant to mount to a pair of shutters in the space between the shutter and the window and function to fasten the shutters during a storm. The back plate, keeper, and straps are made of steel and the bolt itself is made of cast iron. They are powder coated in a glossy black finish.
They do not come with screws.
The back plate at the rear of the bolt measures 5" x 1-3/4"
The bolt measures 6-11/16" x 13/16"
The handle of the bolt projects 1-1/16" from the rear
The keeper measures 2-1/4" x 1-3/4"
The bolt throws 1-15/16" out from the rear plate
-
Large Rectangular Foundation Vent
Large Rectangular Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 14-1/4" wide and 8-5/8" tall. The front measurement is 17-1/2" wide and 11-3/4" tall. The vent recesses into the foundation 3" deep.
-
Brass Sash Pulley
Brass Sash Pulley measures 4-3/4″ x 1-1/4″ at the face, it mortises 2-1/4″ deep into the jamb of the window.
-
# 0 Right Lull and Porter style Shutter Hinge
# 0 Right Lull and Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.
Hinge Width when open - 6-7/16"
Hinge throw from casing - 4-1/8"
Hinge Height at mortise-3-1/2"
These do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
Brass Knuckle Sash Lock
Brass Knuckle Sash Lock is meant for use with double hung windows. The lock comes with two pieces, the latching part, and the receiver which gets overlapped. These were found on most double hung sashes in New Orleans that predated the 1910's. The base of the latching part measures 1-7/8" x 13/16". The base of the receiver measures 1-7/8" x 3/4". It is made of solid brass.
-
# 1 1/2 Left Lull and Porter style Shutter Hinge
# 1 1/2 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.
Hinge Width when open - 5-1/8"
Hinge throw from casing - 3-1/4"
Hinge Height at mortise- 3"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
# 1 1/2 Right Lull and Porter style Shutter Hinge
# 1 1/2 Right Lull and Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.
Hinge Width when open - 5"
Hinge throw from casing - 3-1/4"
Hinge Height at mortise - 2-7/8"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
Iron Pivot Hinge for Transoms
Iron pivot hinge for transoms include one hinge- the pin side and the receiver side. You will need to order two in order to do one sash. These are made of cast iron and left unfinished.
The pin side has the following measurements:
Center to center of screw hole 1-1/2"
Face of Hinge -2-3/8" tall, 7/8" wide, and mortises 1/8" into the face of the transom.
Side of hinge- 5/8" tall, 7/8" wide, 1/8" thick, center of pin to edge 3/4", pin diameter 3/8", pin length 11/16"
The receiver side has the following measurements:
Center to center of screw hole 1-1/8"
Diameter of center hole 7/16"
1-11/16" tall, 3/4" wide and 1/8" deep
-
Medium Victorian Foundation Vent
Medium Victorian Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 17-7/8″ wide and 9-3/8″ tall. The front measurement is 22-7/8″ wide and 14-3/8″ tall. The vent recesses into the foundation 3-1/2″ deep.
-
# 0 Left Lull and Porter style Shutter Hinge
# 0 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.
Hinge Width when open - 6-7/16"
Hinge throw from casing - 4-1/8"
Hinge Height at mortise- 3-1/2"
These do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
Brass Transom Latch
Brass Transom Latch can be used in conjunction with pivoting transom hinges and would mount on the bottom rail of the transom, with the strike plate being mortised to the bottom of the transom's jamb. The latch is operated by pulling up on the loop at the top. (one of our clients suggests mounting a hook to the top of a broom stick to avoid getting on a stool.) The latch measures 2-1/8" wide, 1-1/4" tall, and 5/8" deep (with the loop standing 1-3/8" deep). The strike plate measures 1-3/4" wide, 1-1/2" deep, and mortises 1-3/4" x 3/4"x 3/16" into the jamb. It is made out of solid brass.
-
# 2 Right Lull and Porter style Shutter Hinge
# 2 Right Lull and Porter style Shutter Hinge. Right shutter hinge mounts on the left side of the window when looking at the window from outside of your home.
Hinge Width when open - 4-7/16"
Hinge throw from casing - 2-1/2"
Hinge Height at mortise-2-7/8"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
Out of stock
Brass Oval Beaded Sash Lift
Brass Oval Beaded Sash Lift measures 4" x 2" and mortises into the sash 3/8" deep at 2-3/4" x 1-1/4".
-
Large Victorian Foundation Vent
Large Victorian Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 19″ wide and 10-5/8″ tall. The front measurement is 24-5/8″ wide and 16-1/4″ tall. The vent recesses into the foundation 3″ deep.
-
# 2 Left Lull and Porter style Shutter Hinge
# 2 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.
Hinge Width when open - 4-7/16"
Hinge throw from casing - 2-5/8"
Hinge Height at mortise- 2-15/16"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
# 1 Left Lull and Porter style Shutter Hinges
# 1 Left Lull and Porter style Shutter Hinges. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.
Hinge Width when open - 5-1/2"
Hinge throw from casing - 3-11/16"
Hinge Height at mortise-3-3/16"
These do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
Brass Victorian Sash Lift
Brass Victorian Sash Lift measures 5-1/4" x 1-3/4" and mortises 3/8" deep at 2-3/4" x 1-1/8".
-
6 Inch Cast Iron Hook and Eye
6 Inch Cast Iron Hook and Eye. Contains one hook and one eye. All components are made of cast iron and powder coated in a matte black finish.
Hook length from center of hook to center of hole that attaches hook to the back plate- 5-3/8″
Overall hook length- 6″
Back plate size- 1-3/4″ x 1-3/8″ (1-1/4″ deep)
Eye size- 1-3/4″ x 1-3/8″ (1-1/4″ deep)
-
Clark Tip Left Shutter Hinge
Clark Tip Left Shutter Hinge. For a face mount application when mortising a hinge is not an option. Left Hinges mount on the right side of the window when looking at the window from the exterior. These work well with use on brick homes or homes with wood casing. They are made from cast iron. We suggest you prime and paint these before installation, and screw them in by hand, not with a drill.
These do not come with screws.
Portion of hinge that mounts to the face of your casing- 1-1/2" x 2-1/2"
Portion of hinge that mounts on the face of the shutter- 1-1/2" x 2-1/2"
Throw provided by hinge when open- 3-1/4"
-
Traditional Brass Sash Lock
Traditional Brass Sash Lock is meant for use with double hung style windows. The base of the latch measures 2-5/8" x 7/8" and the base of the keeper measures 2-1/2" x 5/8".
-
Out of stock
Embossed Brass Pull
Embossed Brass Pull measures 6-1/2" tall, 1-1/4" wide, and 1-1/4" deep.
-
4 Inch Cast Iron Hook and Eye with Diamond Shaped Backing
4 Inch Cast Iron Hook and Eye with Diamond Shaped Backing. Contains one hook and one eye. All components are made of cast iron and powder coated in a matte black finish.
Hook length from center of hook to center of hole that attaches hook to the back plate-4″
Overall hook length- 4-1/2″
Back plate size- 2″ x 1-3/8″ (7/8″ deep)
Eye size- 2″ x 1-3/8″ (7/8″ deep)
-
# 1 Right Lull and Porter style Shutter Hinge
# 1 Right Lull and Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.
Hinge Width when open - 5 -1/2"
Hinge throw from casing - 3-5/8"
Hinge Height at Mortise- 3-1/8"
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
# 00 Left Lull and Porter style Shutter Hinge
# 00 Left Lull and Porter style Shutter Hinge. Left shutter hinges mount on the right side of the window when looking at the window from outside of your home.
Hinge Width when open – 8-7/8″
Hinge throw from casing – 6″
Hinge Height at mortise- 3-15/16″
They do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
28 Inch Iron Head Bolt
28 Inch Iron Head Bolt is most often used on a double door application and secures the stationary door at the top, it is highly recommended for use with a foot bolt (or bottom bolt) to prevent warping. The bolt measures 28-1/2" tall and the rear plate measures 1-15/16" wide by 6" tall. The bolt tongue measures 7/8" when activated, and is 3/4" wide. The bolt comes with two different keepers, one used when the door is flush with it's casing, and one used when the door is set deeper into its casing. It also comes with two stays used to keep the arm from being pulled from the surface of the door. It is important to note that in order to operate the bolt properly it must only be pulled up or down, never forward away from the surface of the door (this action would put stress on the weld that attaches the arm to the bolt).
-
4 Inch Cast Iron Hook and Eye with Round Backing
4 Inch Cast Iron Hook and Eye with Round Backing. Contains one hook and one eye. All components are made of cast iron and powder coated in a matte black finish.
Hook length from center of hook to center of hole that attaches hook to the back plate- 3-1/2"
Overall hook length- 4"
Back plate size- 1-3/4" x 1-3/8" (1-1/4" deep)
Eye size- 1-3/4" x 1-3/8" (1-1/4" deep)
-
Clark Tip Right Shutter Hinge
Clark Tip Right Shutter Hinge. For a face mount application when mortising a hinge is not an option. Right hinges mount on the left side of the window when looking at the window from the exterior. These work well with use on brick homes or homes with wood casing. They are made from cast iron. We suggest you prime and paint these before installation, and screw them in by hand, not with a drill.
These do not come with screws.
Portion of hinge that mounts to the face of your casing- 1-1/2" x 2-1/2"
Portion of hinge that mounts on the face of the shutter- 1-1/2" x 2-1/2"
Throw provided by hinge when open- 3-1/4"
-
Solid Brass Knob and Lever Set With Rosettes
Solid Brass Knob and Lever Set with Rosettes. This set mimics screen door and small French door knob and lever sets found in New Orleans. The set comes with one knob, one lever, one circular rosette, one oval rosette, a shaft that connects the knob to the lever with set screws, and two set screws. This set will not work on predrilled doors, nor can it be made into "dummy knobs". It does not come with any latching or locking device.
The knob measures 1-3/4" in diameter and rises 2-1/8" from the surface of the door
The lever measures 3" long 7/8" in diameter at shank and rises 2-1/2" from the surface of the door
The round rosette measures 1-3/4" in diameter
The oval rosette measures 1-3/4" x 1-3/8"
-
Iron Parliament Hinge with Four and Three Quarter Inch Offset
Iron Parliament Hinge with Four and Three Quarter Inch Offset measures a total of 7″ wide and 3-3/8″ tall. It mortises into the door or jamb 1-1/8″ x 3-3/8″ and has a throw of 4-3/4″ when open. The pin on the hinge is removable making it function as either a right or left hand swing.
-
# 00 Right Lull and Porter Style Shutter Hinge
# 00 Right Lull & Porter style Shutter Hinge. Right shutter hinges mount on the left side of the window when looking at the window from outside of your home.
Hinge Width when open – 8-3/4″
Hinge throw from casing – 6″
Hinge height at mortise -3-15/16″
These do not come with screws.
We recommend you prime and paint the hinge before installation, and tighten screws by hand, not with a drill.
-
Out of stock
Iron Parliament Hinge with Four and a Quarter Inch Offset
Iron Parliament Hinge with Four and a Quarter Inch Offset measures a total of 6-3/8″ wide and 2-7/8″ tall. It mortises into the door or jamb 1″ x 2-7/8″ and has a throw of 4-1/4″ when open. The pin on the hinge is removable making it function as either a right or left hand swing.
-
Small Plain Oval Foundation Vent
Small Plain Oval Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 12″ wide and 6-1/2″ tall. The front measurement is 15-7/8″ wide and 10-1/4″ tall. The vent recesses into the foundation 3″ deep.
-
Brass Eastlake Pull
Brass Eastlake Pull measures 4-1/4" tall, 1-5/8" wide, and 1" deep.
-
Out of stock
Three and a Half Inch Steeple Top Embossed Brass Hinges
Three and a Half Inch Steeple Top Embossed Brass Hinges are sold in pairs of two. They feature a removable pin for ease of installation.
-
Out of stock
Solid Brass Beaded Oval Knobs and Plates Set
Solid Brass Beaded Oval Knobs and Plates Set. This set mimics what would be found in some of the Creole homes in and around New Orleans. Cast out of solid brass and polished to a mirror finish, lacquered to prevent immediate tarnishing. It translates nicely when modernizing and updating an older home while trying to maintain the small details that make an older home so appealing. The set comes with two back plates, two knobs, a shaft that connects the two knobs with set screws, and two set screws. These will not work with predrilled doors, but can be made into “dummy knobs” (call for price). This set does not come with any locking or latching device.
The back plates measure 2-1/4″ x 7″ at their widest points
The knobs measure 1-5/8″ x 2-1/2″ at their widest points and rise 2-1/2″ from the surface of the door
-
Embossed Iron Steeple Top Hinges 4" x 4"
Embossed Iron Steeple Top Hinges 4" x 4" are sold in pairs of two (one hinge shown in images). These are made of cast iron and painted semi-gloss black. The pin is removable for ease of hanging. There is embossing on the face of the hinge and the reveal on the side of the hinge. The pattern of the embossing is in a linear Eastlake Victorian style.
-
-
Out of stock
Solid Brass Broken Leaf Knobs and Plates Set
Solid Brass Broken Leaf Door Knobs and Plates Set. Originally patented in 1887 by Lockwood Manufacturing Company, the “Broken Leaf” pattern was widely used at the end of the Victorian era, a style that has come to be known as Eastlake. We have interpreted the original design into a lovely set of solid cast brass hardware. The set is composed of two back plates, two slip on knobs, a shaft that connects the two knobs by set screws, and two set screws. This set will not work for predrilled doors, nor can it be made into “dummy knobs”. They do not come with any latch or locking device.
The plates measure 1-1/2″ x 5-5/16″
The Knobs are 2-1/4″ in diameter
The set projects 2-1/2″ from the face of the door
-
8 Inch Cast Iron Hook and Eye
8 Inch Cast Iron Hook and Eye. Contains one hook and one eye. All components are made of cast iron and powder coated in a matte black finish.
Hook length from center of hook to center of hole that attaches hook to the back plate- 7-7/16″
Overall hook length- 8″
Back plate size- 1-3/4″ x 1-3/8″ (1-1/4″ deep)
Eye size- 1-3/4″ x 1-3/8″ (1-1/4″ deep)
-
Out of stock
Solid Brass Ball Bearing Hinges - ball finial in 3-1/2" x 3-1/2"
Solid Brass Ball Bearing Hinges - ball finial in 3-1/2" x 3-1/2"
These hinges are made from solid brass, polished to a high shine and lacquered to prevent immediate tarnishing. The ball bearing helps to prevent the solid brass hinge from wearing down when used on heavier doors. They are sold as pairs (two hinges per package) and come with screws.
Currently available in 3-1/2" x 3-1/2". Features five knuckles with two ball bearings and three screw holes per side.
-
Out of stock
12 Inch Steel Strap Hinge
12 Inch Steel Strap Hinge includes hinge and pintal. These heavy steel hinges have no offset, but can be bent to accommodate most offsets. We suggest priming and painting these before installation. You may use these on the left or right shutter. This product can be installed using a drill.
The exact measurements of the hinge itself are 12-1/2" long, 1-1/2" wide at widest point, tapers to 3/4" at the end.
The pintal measures 3-3/8" tall, 1-1/2" wide, and projects 1" from the back of the plate to the center of the pintal itself.
-
Large Brass Door Bolt
Large Brass Door Bolts can be used for interior doors that require a locking function (ex. bathrooms or bedrooms) where the door is flush with the casing. This bolt measures 6-1/8″ long and 1-1/2″ wide, stands 1-1/2″ tall from the surface of the door, and throws 1-5/8″. The keeper measures 1-1/4″ long and 1-1/2″ tall.
-
Brass Casement Sash Latch
Brass Casement Sash Latch comes with the latch, and three different keepers (one meant for use with a pair of casements which is surface mount and two meant for use with a single casement which mortises into the jamb).
The latch's back plate measures 2-1/16" tall, 1-5/16" wide and projects 2" from the surface of the window. The surface mount keeper measures 2" tall, 9/16" wide and projects 7/8" from the surface of the window. The first mortised keeper measures 2-1/8" tall, a total of 1-3/4" deep, and mortises 1" x 1/8" into the jamb and the second mortised keeper measures 5/8" x 2-3/8" x 1/16".
-
Out of stock
8 Inch Iron Foot Bolt
8 Inch Iron Foot Bolt is most often used on a double door application and secures the stationary door at the bottom, it is highly recommended for use with a head bolt (or top bolt) to prevent warping. The bolt measures 9-1/4″ tall and the rear plate measures 1-7/8″ wide by 5-1/2″ tall. The bolt tongue measures 1-1/16″ when activated, and is 3/4″ wide. The bolt comes with two different keepers, one used when the threshold extends well past the door and can be mortised into, and one used when the threshold does not extend much past the door. It is important to note that in order to operate the bolt properly it must only be pulled up or down with your hand, never forward away from the surface of the door, or operated with your foot (this action would put stress on the weld that attaches the arm to the bolt).
-
Large Plain Oval Foundation Vent
Large Plain Oval Foundation Vent is made of cast aluminum and sold unfinished. It can be primed and painted with exterior primer and paint. These are traditionally set into the foundation using cement as a binder. The rear measurement is 14″ wide and 8-1/4″ tall. The front measurement is 18-1/4″ wide and 12-3/8″ tall. The vent recesses into the foundation 3-3/8″ deep.
-
Embossed Kick Bolts
Embossed kick bolts- available in two sizes and two finishes
The embossed kick bolts in the brass finish are made from solid, cast brass. The embossed kick bolts in the powder coated black are made from cast iron. These embossed kick bolts are designed to go at the bottom of the stationary door, shutter, or window when there are pairs of doors, shutters, or windows. We highly recommend you use these with a chain bolt (or top bolt) to prevent warping of your door.
The small bolts have the following measurements:
The bolt body measures 1-7/8 ” wide and 5-1/16″ tall, the tongue sticks out 1/2″ from the body of the latch when activated. The bolt is designed to be operated with your foot, the large button at the top activates it and the small button on the face deactivates it. The bolt comes with two strike plates- one measuring 1-7/8″wide and 2-3/8″ deep, and one measuring 2″ wide and 7/8″ deep.
The large bolts have the following measurements:
The bolt body measures 2 ” wide and 7-1/16″ tall, the tongue sticks out 3/4″ from the body of the latch when activated. The bolt is designed to be operated with your foot, the large button at the top activates it and the small button on the face deactivates it. The bolt comes with two strike plates- one measuring 1-7/8″wide and 2-3/8″ deep, and one measuring 2″ wide and 7/8″ deep.
-
Iron Casement Sash Latch
Iron Casement Sash Latch comes with the latch, and two different keepers (one meant for use with a pair of casements which is surface mount and one meant for use with a single casement which mortises into the jamb).
The latch's back plate measures 2-1/8" tall, 1-1/4" wide and projects 2" from the surface of the window. The surface mount keeper measures 2" tall, 9/16" wide and projects 7/8" from the surface of the window. The mortised keeper measures 2-1/8" tall, a total of 1-3/4" deep, and mortises 1" x 1/8" into the jamb.
-
Out of stock
17 Inch Steel Hook and Eye
17 Inch Steel Hook and Eye. Contains one hook and one eye. All components are made of steel and left unfinished.
Hook length from center of hook to center of hole that attaches hook to the back plate- 16″
Overall hook length- 17″
Back plate size- 1-1/2″ x 3-1/4″ (1-3/8″ deep)
Eye size- 1-1/2″ x 3-1/4″ (3/4″ deep)
-
Brass Casement Stay
Brass Casement Stay is made to secure casement windows in either a closed or open position. The Maximum throw is 10-1/2". These are meant for use in an outswing application only.
-
10 Inch Shutter Slide Bolt
10 Inch Shutter Slide Bolt. These slide bolts are meant to mount to a pair of shutters in the space between the shutter and the window and function to fasten the shutters during a storm. The back plate, keeper, and straps are made of steel and the bolt itself is made of cast iron. They are powder coated in a glossy black finish.
They do not come with screws.
The back plate at the rear of the bolt measures 6-3/4″ x 1-3/4″
The bolt measures 6" x 3/4″
The handle of the bolt projects 5/8″ from the rear
The keeper measures 2-5/8″ x 1-3/4″
The bolt throws 2-15/16″ out from the rear plate
-
Iron Oval Pull
Iron Oval Pull measures 1-3/4" tall, 1-1/8" wide, and 1-1/2" deep. It mounts with an attached wood screw.
-
Three Inch Steeple Top Embossed Brass Hinges
Three Inch Steeple Top Embossed Brass Hinges are sold in pairs of two. They feature a removable pin for ease of installation.
-
Large Iron Fleur de Lis Pull
Large Iron Fleur de Lis Pull measures 9" tall, 1-5/8" wide, and 1-7/8" deep. The screw holes measure 7-5/8" center to center. They are painted black.
